Moog MSD C2, Руководство по эксплуатации

Страница: 36 / 72

36
MSD Single-Axis Servo Drive Compact Operation Manual
ID no.: CA97555-001 Date: 04 /201 8
moog
X7 Pin
Sin/Cos
and TTL
Sin/Cos
absolute value
encoder
SSI/EnDat
Absolute value
encoder EnDat
(digital)
Absolute value
encoder HIPER-
FACE®
1 A- A- - REFCOS
2 A+ A+ - +COS
3
+5 V DC ±5 %, IOUT maximum = 250 mA (150 mA for
hardware versions 0..1), monitoring via sensor cable
7 to 12 V
(typ. 11 V)
maximum 100 mA
The sum of the cur-
rents tapped at X7/3
and X6/4 must not
exceed the specified
value!
4 R+ Data + Data + Data +
5 R- Data - Data - Data -
6 B- B- - REFSIN
7 - - - U
S
switch
8 GND GND GND GND
9
ϑ
- (PTC, KTY, Klixon) internally connected to X6/9
1)
10
ϑ
+ (PTC, KTY, Klixon) internally connected to X6/5
1)
11 B+ B+ - +SIN
12 Sense + Sense + Sense + U
S
switch
13 Sense - Sense - Sense - -
After connecting
pin 7 to pin 12, a
voltage of 11.8 V is
set on X7, pin 3!
14 - CLK+ CLK+ -
15 - CLK - CLK - -
1) Be sure to pay attention to the note headed "ATTENTION" in Table 4.14!
Table 4.13 Pin assignment of the X7 terminal connection
NOTE:
The encoder supply on X7/3 is short-circuit proof on both 5 V and 11 V
operation. The drive remains in operation enabling the generation of a
corresponding error message on evaluating the encoder signals.
4.13.3 Connection for high-resolution encoder
The interface X7 enables evaluation of the following encoder types.
Figure Function
X7
Encoder/ SSI
Sin/Cos encoder with zero pulse
e.g. Heidenhain ERN1381, ROD486
Heidenhain Sin/Cos encoder with EnDat interface
e.g. 13 bit single-turn encoder (ECN1313.EnDat01) and 25 bit multi-turn encoder
(EQN1325-EnDat01)
Heidenhain encoder with digital EnDat interface
Single- or multi-turn encoder
Sin/Cos encoder with SSI interface
e.g. 13 bit single-turn and 25 bit multi-turn encoder (ECN413-SSI, EQN425-SSI)
Sick-Stegmann Sin/Cos encoder with HIPERFACE® interface
Single- and multi-turn encoder, e.g. SRS50, SRM50
Table 4.12 Suitable encoder types on X7
NOTE:
y The usage of encoders not included in the range supplied by Moog
requires special approval by Moog.
y
The maximum signal input fr equency is 500 kHz.
y
Encoders with a power supply of 5 V ±5 % must have a separate sensor
cable connection. The encoder cable detects the actual supply voltage
at the encoder, thereby compensating for the voltage drop on the cable.
Only use of the sensor cable ensures that the encoder is supplied with the
correct voltage. The sensor cable must always be connected.
Select the cable type specified by the motor or encoder manufactu er. During this
process bear in mind the following:
y
Always used shielded cables. The shield is to be connected at both ends.
y Connect the differential track signals A/B, R or CLK, DATA to each other using twisted pairs.
y
Do not split the encoder cable, for example to route the signals via terminals in the switch
cabinet.