manualshive.com logo in svg

MONTAGUE Legend RD18, Инструкция по эксплуатации

Поделиться
Скачать
MONTAGUE Legend RD18 Скачать руководство пользователя страница 30

28

SERVICE

Problem Probable Cause Corrective Action

6. Take a pyrometer reading when the burners extinguish for the third time.

7. Loosen the setscrews in the thermostat knob and turn knob to the temperature established
by the pyrometer reading.

8. Allow burners to cycle on and off three more times and recheck pyrometer reading against
thermostat setting. Temperature readings should be within 5°F.

Replacing Fryer Components

Replacing the Operating Thermostat

1. Drain fryer and turn gas off.

2. Use an allen wrench to loosen setscrew at the side of the thermostat knob. Remove the
thermostat knob.

3. Remove the two setscrews on either side of the thermostat shaft and remove the dial plate.

4. Disconnect the thermostat wires from gas valve.

5. Use a slotted socket to unscrew the thermostat from
the frypot.

6. Apply a small amount of Locitte PST56765 compound to the threads of the new thermostat.
Install the thermostat.

7. Recalibrate.

Setscrews hold the knob and the dial plate

to the thermostat. Use an allen wrench to

remove both.

Содержание Legend RD18















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды