Mitsubishi Electric Melsec WS Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 142

background image

Ethernet interface module

MELSEC-WS

32

Configuration of the TCP/IP interface - who establishes the connection

If the Ethernet interface module shall connect to the external application, perform the
following configuration steps:



Activate the

Connect

to

radio button.



Set

IP

address

to the IP address of the computer the application is running on.



Enter the

Port

number for the application.

The configuration is considered faulty if either the connect socket port and/or the
connect IP address is zero when in

Connect

mode.

If the external application shall connect to the Ethernet interface module, perform the
following configuration steps:



Activate the

Listen to

radio button.



Enter the

Port

number for the application.



Suggested port numbers are 9100 to 9103 (default values).



Port 0 and port 9000 are reserved and can not be used (faulty configuration).



Port numbers 0 to 1023 are managed by the Internet Assigned Numbers
Authority (IANA) and can not be used. See www.iana.org/assignments/port-
numbers

Finally, determine how the data is transferred. Follow the steps outlined in the
following section.

Data transfer method - how the data is transferred

Whenever the TCP/IP socket connection has been established (either by an
application on a PC or by the Ethernet interface module itself), there are two
possible methods how the data sets can be transferred:



The application requests the data set(s) per command message (Application
requests (Polling) mode),

or



the Ethernet interface module auto-updates the data sets as per configuration
(Ethernet interface module writes to Address/Port (Auto update) mode).

In the auto update mode, there are two update modes how the Ethernet interface
module update the data:



Update COS (Change of state): when any data of the input data set change
status.



Heartbeat interval: data will be sent automatically according to the configured

Heartbeat rate

in ms.

If Heartbeat interval is enabled, a change of state will trigger an immediate update of
the data as well, regardless of the set heartbeat rate. (I.e. COS is always active.)

For both methods the following structure of messages applies.

Note

Note

Note

«
...
33
34
35
36
37
...
»

Содержание Melsec WS Series















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Melsec WS Series

Бренд: Falcon Страницы: 3

Бренд: OBaby Страницы: 47

Бренд: Datavideo Страницы: 8

Бренд: UCS Страницы: 4

Бренд: Magellan Страницы: 2

Бренд: Klimaire Страницы: 5

Бренд: Multi-Clean Страницы: 4

Бренд: Primo Water Страницы: 10

Бренд: PENGWYN Страницы: 32

Бренд: Warner Electric Страницы: 6

Бренд: CORNING Страницы: 12

Бренд: Mosa Страницы: 28

Бренд: Simpnic Страницы: 16

Бренд: Chamberlain Страницы: 4

Бренд: Shimaden Страницы: 16

Бренд: Pacostar Страницы: 55

Бренд: SainSmart Страницы: 49

Бренд: Aeroflex Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды