manualshive.com logo in svg

Mitsubishi Electric Melsec WS Series, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric Melsec WS Series Скачать руководство пользователя страница 29

Ethernet interface module

  

MELSEC-WS 

26 

3.4.5 

Verification of a configuration 

After the configuration has been transferred successfully, the MELSEC-WS safety 
controller can be verified. To this purpose, the downloaded configuration data are 
read back out from the safety controller and compared with the project data. If they 
match, the data are displayed in a report. If the user confirms that they are correct, 
the safety controller is considered to be verified. 

 In the 

Hardware

 

configuration

 view, click the icon 

Upload and verify 

configuration

 and compare the configuration. The 

Upload and verify result

 

window is opened. 

 Click 

Yes

 below at the question 

Set device to verified?

 if the displayed 

configuration is the expected configuration. The safety controller is then 
considered to be verified. 

 

You have to be logged in as an Administrator in order to mark the device as 
“verified”. 

 

If the verification is completed successfully, a “Read in and compare” report that 
provides the most important project information is created subsequently. You can 
print out or store this report. 

 

The status verified/not verified is indicated in the lower right-hand corner of the 
Setting and Monitoring Tool and by the CV LED of the CPU module turning on. 

 

Only if the device and the corresponding configuration have been marked as 
verified, the Auto RUN Mode is active in the configuration of the CPU module. If 
the configuration is not set to verified, the safety controller stays in Idle mode (CV 
LED on the CPU module flashing) after power up and needs to be set to 

Run

 

Mode

 using the Setting and Monitoring Tool. 

 

If differences between the project data and the read-back configuration data are 
detected, a corresponding message including information about possible actions 
is displayed. Verification of the configuration is not possible then. Observe the 
information in the error message for the further procedure. Terminate the dialog 
box by clicking 

Close

. 

 

If you change a verified configuration, the status is reset to “not verified”.  

Exception

: If you make only non safety-related changes such as modifying the 

Ethernet interface module name, the Ethernet interface module’s IP address or 
the port number for a TCP/IP socket connection, the configuration status remains 
“verified”. 

More information can be found in the Safety Controller Setting and Monitoring Tool 
Operating Manual. 

 

3.4.6 

Upload of a configuration 

When in online mode, you can upload a configuration from the connected MELSEC-
WS safety controller: 

 Click on 

Upload

. The current configuration of the safety controller will be loaded 

into the Setting and Monitoring Tool and can be edited after going offline. 

 
 

 

Note 

Содержание Melsec WS Series















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды