manualshive.com logo in svg

Mitsubishi Electric Melsec WS Series, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric Melsec WS Series Скачать руководство пользователя страница 16

MELSEC-WS 

On safety

 

13 

Pay attention to the safety notes and safety measures on the Ethernet 
interface module! 

If the device is used for any other purposes or modified in any way - also during 
mounting and installation - any warranty claim against Mitsubishi Electric 
Corporation shall become void. 

 

 

When mounting, installing and using the Ethernet interface module, observe the 
standards and directives applicable in your country. 

 

The national/international rules and regulations apply to the installation, 
commissioning, use and periodic technical inspection of the MELSEC-WS safety 
controller, in particular: 

– EMC 

directive 

2004/108/EC, 

–  Provision and Use of Work Equipment Directive 89/655/EC, 
–  the work safety regulations/safety rules. 

 

This manual must be made available to the operator of the machine where the 
MELSEC-WS safety controller is used. The machine operator is to be instructed 
in the use of the device by qualified safety personnel and must be instructed to 
read the manual. 

 

Since an Ethernet interface module is powered from the CPU module, connect a 
Class 2 power supply or a Class 2 transformer in accordance with UL310 or 
UL1585 to the CPU module. 

 

The MELSEC-WS safety controller fulfils the requirements of Class A 
(industrial applications) in accordance with the “Interference emission” 
basic specifications.

 

The MELSEC-WS safety controller is therefore only suitable for use in an 
industrial environment and not for private use. 

 
 

 

 

ATTENTION 

Note 

 

ATTENTION 

Содержание Melsec WS Series















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды