7 APPLICATION INSTRUCTIONS
7.28 Routing Information Instructions
1075
7
Processing details
• These instructions write the routing information stored in the device specified by (s2) and later to the area with the transfer
destination network number specified by (s1).
• The following figure shows the data stored in the device specified by (s2) and later.
• The specification ranges of relay station number are as follows.
• If the data of the transfer destination network number specified by (s1) has already been set in parameter, the data is
overwritten with the data stored in the device specified by (s2) and later.
• If the data in the device areas specified by (s2) to (s2)+2 are all 0, the data of the transfer destination network number
specified by (s1) is deleted from parameter.
Operation error
Start device
Item
Range
(s2)
Relay network number
1 to 239
(s2)+1
Relay station number
Refer to the following table.
(s2)+2
Dummy
Network type
Specification range
MELSECNET/H
1 to 64
CC-Link IE Controller Network
1 to 120
CC-Link IE Field Network (master station)
Fixed to 125
CC-Link IE Field Network (local station)
1 to 120
Error code
(SD0)
Description
3405H
The value set to (s1) is out of the range, 1 to 239.
Any of the data in the device areas specified by (s2) and later exceeds the following range.
• (s2)+0: 1 to 239
• (s2)+1: 1 to 120, 125
The total number of routing information registered in parameter of the network module and registered by using the RTWRITE instruction
exceeds 238.
A transfer destination network number which is not registered in parameter is specified as a deletion target.
A zero is specified in only either of the device areas specified by (s2) and (s2)+1.
Содержание MELSEC iQ-R Series
