MIMAKI Tx300P-1800B, Руководство по эксплуатации, Страница: 63 / 144

3-3
1
2
3
4
5
6
Chapter 3 Setup
SETUP MENU table
• For each setting item below, you can set it so that the machine may operate according to the value specified when you
printed from your RIP software in the connected host PC.
• Set Item : LOGICAL SEEK/ Overprint/ DRYING TIME/ MARGIN (LEFT and RIGHT)/ FEED SPEED
• When you operate the machine according to the contents specified with the RIP software, set each
• item to “Host” when registering this machine type. When you set it other than “Host”, the machine operates according to
the machine setup.
• For the specifying method with the RIP software, refer to the operation manual of the RIP software.
Function name Set value
When no
instruction from
RIP exists
*1
*1. This is the setting value to be used for printing when setting value is not specified at the RIP software (host) side, or, you give priority to the setting value at
the machine side.
Outline
FEED COMP. ( P.3-5) -9999 to 0 to 9999
Used to print a pattern for correcting a media-
feeding rate and correct it.
DROP.POScorrect ( P.3-6) -40.0 to 0 to 40.0
Used to adjust the dot position in go and return
printing.
LOGICAL SEEK ( P.3-7) HOST/ON / OFF OFF Sets the scan movable area during printing.
Overprint ( P.3-7) HOST/ 1 to 9 1
Sets the number of layers in which ink is to be
applied.
DRYING TIME
(
P.3-7)
SCAN HOST/ 0.0 to 9.9 sec 0 sec
Sets the time to wait for ink drying.
PRINT END HOST/ 0 to 120 min 0 min
FEED SPEED ( P.3-8) HOST/ 10 to 100% 100% Changes the media feeding speed in printing.
AUTO
CLEANING
(
P.3-10)
DEFAULT, FILE,
LENGTH, TIME
Sets the automatic cleaning operation for the head
performed before printing or during printing.
DEFAULT
The value differs depending
on the type of ink to be used
and the operating
environment.
FILE INTERVAL 1 to 1000
TYPE NORMAL/ SOFT/ HARD
LENGTH INTERVAL 0.1 to100.0m
TYPE NORMAL/ SOFT/ HARD
TIME INTERVAL 10 to 480 min
TYPE NORMAL/ SOFT/ HARD
Cleaning Check ON/ OFF
Set to run or not a nozzle check after auto
cleaning.
EXEC.TIMING END OF FILE/PRINTING
Sets the timing for cleaning operation performed
when “LENGTH” or “TIME” is selected.
INTERVAL WIPING ( P.3-11) 3 to 255 min, OFF
Sets the wiping operation performed after printing
is completed.
EXTERNAL HEATER ( P.3-11) ON/OFF Used to set external heater to ON/OFF.
MAPS4
(
P.3-9)
AUTO
Perform setting to reduce stripes between passes.
MANU
AL
SPEED 50 to 100%
Smoothing
Lv.
0 to 25 to 100%
BELT COMP. ( P.3-11) ON/OFF Improves print quality by reducing unevenness.
BELT WASH
(
P.3-11)
BELT WASH ON/OFF
Set to automatically perform/not perform a belt
wash.
BELT FEED SPEED
*2
*2. When doing an overprint or the feeding belt is badly dirty due to a bleed-through, set it in “LOW”. If performing a jog feeding in “NORMAL”, the feeding belt
may not be washed enough.
NORMAL/LOW
Set the feeding speed for a feeding by the jog
operation except printing or a confirmation
feeding.
COUNTER
LIMIT
(
P.3-12)
Adhesive OFF, 1 to 30000m
Resets the adhesive and absorb roller
replacement notification time settings.
Absorb Roller OFF, 1 to 30000m
RESET SETTING ( P.3-5) The configuration in the settings 1-4 can be reset individually.
SAVE ( P.3-5) Allows content set in Temporary to be saved to SETUP 1 to 4.