MIMAKI CJV30-100BS Скачать руководство пользователя

Страница: 196 / 296

6-2

Maintenance

Maintain the machine regularly or as necessary so that its accuracy will be maintained and it can continue to be
used for a long time.

Precautions for Maintenance

Pay attention to the following items when maintaining this machine.

About Cleaning Solution

Use the cleaning solution corresponding to the BS

ink.

• When using cleaning solution for maintenance, be sure to wear the supplied protective glasses.

• The ink contains organic solvent. When cleaning the machine, be sure to wear gloves so that no ink will

make direct contact with your skin.

• Never disassemble the machine. Disassembling it can result in electric shock hazards or damage to the

machine.
Before maintenance, be sure to turn off the power switch and unplug the power cable; otherwise, an
unexpected accident may occur.

• Prevent moisture from entering the machine. Moisture inside the machine can cause electric shock

hazards or damage to the machine.

• To ensure stable ink jetting, it is necessary for the machine to eject a small amount of ink (flushing)

regularly when a printing (outputting) operation has not been performed for a long time.

• When the machine is not to be used for a long time, turn off only the power switch on the front side, leave

the main power switch at the rear turned ON (in the position of | ), and leave the power cable connected.

• If organic solvent ink is mixed with water or alcohol, coagulation is generated.

Do not wipe the nozzle face of the heads, wiper, caps, etc. with water or alcohol. Doing so can cause
nozzle clogging or machine failure.

• Do not use benzene, thinner, or any chemical agent containing an abrasive. Such materials can

deteriorate or deform the surface of the cover.

• Do not apply a lubricant, etc. to any parts inside the machine. Doing so can cause damage to the plotter

mechanism.

• Be careful that the cleaning solution, ink, etc. not to stick to the cover because this may cause the

surface of the cover to deteriorate or deform.

Ink type

Applicable cleaning solution for maintenance

ink

Cleaning Solution 200 for Solvent Ink (SPC-0369)
MILD SOLVENT WASHING LIQUID (SPC-0294)

Содержание CJV30-100BS









































































































































































































































































































Результаты поиска

Содержание CJV30-100BS

Отзывы:

Похожие инструкции для CJV30-100BS

Бренды по названию

Популярные бренды

MIMAKI CJV30-100BS, Руководство по эксплуатации

Результаты поиска

Содержание CJV30-100BS

Отзывы:

Похожие инструкции для CJV30-100BS

Бренды по названию

Популярные бренды