MIMAKI CJV30-100BS Скачать руководство пользователя страница 104

Страница: 104 / 296

Other Settings

3-28

List of Settings

The underlined has been set as default.

Function Name

Overview

Set Value

PINCH ROLLER

Setting the pinch roller pressure and the pinch
roller numbers according to the medium to be
used.

See P.3-5.

MEDIA COMP.

A medium-feeding rate is corrected.

See P.3-8.

DROP. POS CORRECT

Setting used when the thickness of the medium,
head height, or ink type is changed.

See P.3-10.

HEATER

The heater temperature is set.

See P.3-12.

The standby time and OFF time of the heaters
are set.

PRINT MODE

Printing quality is set.

See P.3-16.

A scanning direction is set.
Logical seek is set.

INK LAYER

The number of ink layers is set.

Once to nine times

DRYING TIME

Ink drying time for each scanning is set.

See P.3-20.

Ink drying time after printing has been complete
is set.

AUTO CUT

Whether a medium is automatically cut after
printing is set.

ON/OFF

PRE-FEED

Whether a medium is fed back and forth before
printing is set.

ON/OFF

COLOR PATTERN

It is set whether a color pattern is printed on the
right edge of a medium.

*1. When ON is set, maximum printing width becomes 18mm narrower.

When cutting only with RasterLinkPro4

or later, maximum cutting width also becomes 18mm narrower. If it affects the data layout,

set to OFF.

ON/OFF

REFRESH

The refreshing level of the heads is set.

0 to 3

VACUUM

The ability to adsorb a medium is set.

STORONG / STANDARD /
LittleWEAK / WEAK /OFF

FEED SPEED

The speed at which a medium is fed during
printing, etc. is set.

10 to 100 to 200%

PRIORITY

The prioritized setting (by the host or the panel) is
determined.

INDIVIDUALLY / ALL HOST /
ALL PANEL

AUTO CLEANING

Automatic head cleaning conducted for each
printing operation is set.

See P.3-24.

PRINT. CLEANING

Automatic head cleaning conducted during
printing is set.

See P.3-26.

Содержание CJV30-100BS









































































































































































































































































































Результаты поиска

Содержание CJV30-100BS

Отзывы:

Бренды по названию

Популярные бренды

MIMAKI CJV30-100BS, Руководство по эксплуатации

Результаты поиска

Содержание CJV30-100BS

Отзывы:

Бренды по названию

Популярные бренды