MIMAKI CJV30-100BS Скачать руководство пользователя | Manualshive

Страница: 111 / 296

background image

3-35

Machine Settings

3

Ex
tended F

unctions

– Printer –

When using 600 cc cartridge (firmware Ver.2.10 or older )

Requisite for the 600 cc cartridge

Mounting/removing 600 cc ink pack

For mounting/removing the 600 cc ink pack, refer to the label adhered on the eco case.

Precaution for using 600 cc cartridge

Be sure to put the ink pack and the ink chip in the eco case for setting the 600 cc cartridge on the ink station.

Registering weight of eco case

Register the eco case weight on this machine to calculate the remaining ink quantity from the weight of the 600
cc cartridge.

Eco Case

The 600 cc ink pack and the attached ink chip are put in the eco case and used.
This is referred to as "600 cc cartridge" in this manual.

600 cc Ink Pack

Ink Chip

*1

*1.Attached to the 600cc ink pack.

Scale

To calculate the remaining ink quantity, input the weight of the eco case and the
600 cc cartridge into this machine. Use a scale for weight measuring. (To manage
the accurate remaining ink quantity, prepare the scale that can weigh in one gram
unit.)

• This machine cannot judge whether the 600 cc ink pack is in the eco case or not.

When using the 600 cc cartridge, be sure to attach the ink pack.

• Setting an eco case without ink chip on the machine will break this machine. Be sure to attach the ink

chip to the eco case before use.

Register the weight of the eco case in the following cases.

• For using the 600 cc cartridge for the first time
• When the case weight is changed by replacing the eco case.

• The weight of each eco case slightly differs respectively. To control accurate ink quantity, be sure to

register the weight of each eco case.

«
...
109
110
111
112
113
...
»

Содержание CJV30-100BS









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CJV30-100BS

Бренд: Roland Страницы: 2

SRM-2100 TYPE 1E - 02-99

Бренд: Echo Страницы: 29

Бренд: The Handy Страницы: 28

Бренд: Fein Страницы: 4

Бренд: Fein Страницы: 134

Бренд: QEP Страницы: 8

Бренд: Peach Страницы: 34

Бренд: Martin Yale Industries Страницы: 4

Cornerounder CR-177

Бренд: Lassco Wizer Страницы: 4

Бренд: Larzep Страницы: 5

Бренд: Larzep Страницы: 5

Бренд: Larzep Страницы: 7

Бренд: Parkside Страницы: 64

Бренд: Far Tools Страницы: 74

Бренд: ATIKA Страницы: 96

Бренд: Duratool Страницы: 4

IDEAL 4810 (18-3/4'')

Бренд: Officezone Страницы: 8

LINEA PRO GST43

Бренд: Black & Decker Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды