MIMAKI CJV30-100BS страница 32 Скачать руководство пользователя

Страница: 32 / 296

1-16

Menu Mode

This machine has 4 modes. Each menu mode is described below.

Not-ready

This is the mode in which the medium has not been detected yet.

• The keys other than the

key are effective.

LOCAL

LOCAL is the mode for the preparation state.
There are two LOCAL modes: [Printer mode] and [Cutting mode].

• Press the

key to switch to the printer mode and the cutting mode.

• All the keys are effective.
• The machine can receive data from the computer. However, it does not perform printing or cutting.

Function

To set Function mode, press the

key when this machine is in Local mode.

In this mode, printing conditions can be set.

REMOTE

The received data is printed or cut.
Printing or cutting can be interrupted by pressing the

key.

LOCAL display in printer mode

Displays current user type
(

P.2-2).

Displays machine name (

P.5-

12) to recognize the device.

Displays the detected medium
width.

LOCAL display in cutting mode

Indicates that the machine is
in cutting mode.

Displays machine name (

P.5-

12) to recognize the device.

Indicates the current tool condition
and set value (

P.2-3).

Содержание CJV30-100BS









































































































































































































































































































Результаты поиска

Содержание CJV30-100BS

Отзывы:

Похожие инструкции для CJV30-100BS

Бренды по названию

Популярные бренды

MIMAKI CJV30-100BS, Руководство по эксплуатации

Результаты поиска

Содержание CJV30-100BS

Отзывы:

Похожие инструкции для CJV30-100BS

Бренды по названию

Популярные бренды