MIMAKI CJV30-100BS Скачать руководство пользователя | Manualshive

Страница: 12 / 296

background image

xi

Precautions for Use

Caution

About Power Supply

Prohibition of Use in a Poorly Ventilated Room

• Do not turn off the main power switch on the right

side of this machine.

• If you get ink in your eyes, immediately wash

your eyes with a lot of clean water for at least 15
minutes. In doing so, also wash eyes to rinse ink
away completely. Then, consult a doctor as soon
as possible.

• If anyone drinks ink by mistake, keep him or her

quiet and see a doctor immediately Do not allow
him or her to swallow the vomit. After that,
contact the Poison Control Center.

• If you inhale a lot of vapor and feel bad,

immediately move to a location of fresh air and
then keep yourself warm and quiet. Then, consult
a doctor as soon as possible.

About the Heaters

• Do not spill liquid on the platen as this may cause

failure of the heater or firing.

• Do not touch platen heaters with bare hand while

it is hot; otherwise, you can get burned.

• When the machine is to be moved, wait until the

heater temperature drops adequately. As a
criterion, wait at least 30 minutes after you turn
off the power to the heater. Moving the machine
must be limited to on the same floor where there
is no steps. When the machine is to be moved to
any place other than on the same step-free floor,
contact your distributor or a sales office of
MIMAKI.

• The ink contains organic solvent. If ink has stuck

to your skin or clothes, immediately wash it off
with detergent and water.

How to Handle Ink

Caution about the Moving Parts

• When cleaning the ink-station or the heads, make

sure to wear the attached gloves. Further, when
the solvent ink is used, it is necessary to wear the
attached goggles.

• Do not touch the rolling grid roller; otherwise, you

may hurt your fingers or tear off your finger nails.

• Keep your head and hands away from any

moving parts during a printing or cutting
operation; otherwise, you may get your hair
caught in the machine or get injured.

• Wear proper clothes. (Do not wear loose-fit

clothes or accessories.) Also, bind a long hair.

• Each unit is automatically switched to in concert

with the movement of printing or cutting. Do not
make your face or hands near above the platen.
Also, do not place a small object or a tool.

About Media

• Straighten the sheet of media, if significantly

curled, before using it for printing. Heavily curled
sheet affects the printing or cutting result.

About the Cutter

• Do not touch the cutter blade, which is very

sharp.

• Do not shake or swing the cutter holder;

otherwise, the blade may come off.

«
...
10
11
12
13
14
...
»

Содержание CJV30-100BS









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CJV30-100BS

Бренд: Partner Страницы: 20

Бренд: Wolfcraft Страницы: 76

Бренд: maimin Страницы: 12

Бренд: Mafell Страницы: 102

Бренд: Shindaiwa Страницы: 40

Бренд: UnionSpecial Страницы: 18

Greensmaster 3250-D

Бренд: Toro Страницы: 52

Бренд: EASTMAN Страницы: 56

Бренд: EASTMAN Страницы: 88

Vitrex Clinker XL

Бренд: QEP Страницы: 5

Бренд: Logan Страницы: 2

Бренд: Logan Страницы: 16

Бренд: O-Mac Страницы: 88

TMC24 TURF multi Cutter

Бренд: Groundsman Страницы: 22

Бренд: Haussmann Xpert Страницы: 12

Бренд: Hypertherm Страницы: 69

Horizon PC-P430

Бренд: Standard Страницы: 36

Бренд: Stihl Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды