MIMAKI CJV30-100BS страница 233 Скачать руководство пользователя | Manualshive

Страница: 233 / 296

background image

6-39

Other Maintenance Functions

6

6

Mai
n

tenanc

e

If a Waste Ink Tank Confirmation Message Appears

Ink used in head cleaning, etc. is stored in the waste ink tank on the lower right side of the machine. This
machine counts the accumulated amount of discharged ink. When that reaches a specified amount, the machine
displays a confirmation message.

(When this message is displayed, consider the replacement of the waste

ink tank.)

If a Message Is Displayed, for Example, When the Machine Is Supplied with Ink

When functions that use the waste ink tank, such as ink-supplying, head cleaning, and PUMP tube washing, are
performed, a message that requests you to confirm the state of the waste ink tank may be displayed, depending
on the state of the tank.

z

When the waste ink tank is almost full:

The message on the right is displayed.

1

Check the state of the waste ink tank.

When the waste ink tank is almost full:

(1)

Replace the waste ink tank with another. (

P.6-41)

(2)

Press the

key to select "Exchange". (The amount of discharged ink is reset.)

When the waste ink tank still has a capacity for waste ink:

(1)

Press

to select "Continue". (The amount of discharged ink is not reset.)

• In this case, returning to LOCAL will display the message of P. 6-39 "Confirmation Message in

LOCAL".

z

When the waste ink tank is completely full:

The message on the right is displayed.

1

Replace the waste ink tank with another (

P.6-41) and press the

key.

• The amount of discharged ink is reset.

Confirmation Message in LOCAL

The message on the right is displayed.

1

Check the state of the waste ink tank and replace it with another as necessary.
(

P.6-41)

• When you have selected "Exchange" for "almost full" or "completely full" in the above operation, make

sure to replace the waste ink tank. (

P.6-41) When you use the machine without replacing the waste

ink tank, waste ink may overflow from the tank before a confirmation message is displayed.

• This machine does not count the accumulated amount of waste ink discharged when the

ST.MAINTENANCE (NOZZLE WASH, PUMP TUBE WASH, and COSTODY WASH (firmware Ver.2.20
or older)) are performed. Before performing these functions, make sure to check the state of the waste
ink tank.

C o n f i r m a w a s t e t a n k
C o n t i n u e <

> E x c h a n g e

C o n f i r m a w a s t e t a n k
E x c h a n g e

:

e

n t

< LOCA L . 1 >

[ # 0 1 ]

! WAS T E T ANK

«
...
231
232
233
234
235
...
»

Содержание CJV30-100BS









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CJV30-100BS

Бренд: Dimas Страницы: 23

NZ 3200 - AXIS ERGO

Бренд: Robland Страницы: 21

Бренд: Erbauer Страницы: 21

eclips EC-C1200

Бренд: Ellison Страницы: 36

Бренд: Maktec Страницы: 8

Бренд: Silca Страницы: 2

Бренд: Esko Страницы: 59

Бренд: Pace Technologies Страницы: 61

Бренд: PrimAster Страницы: 44

Бренд: LEITZ Страницы: 30

Бренд: AL-KO Страницы: 244

Бренд: ATIKA Страницы: 208

Бренд: Dremel Страницы: 4

Бренд: Amkus Страницы: 4

Бренд: Pace Technologies Страницы: 30

Бренд: P1PE Страницы: 32

Бренд: GBC Страницы: 24

Бренд: EINHELL Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды