Miele PT 5137 WP Скачать руководство пользователя страница 61

Страница: 61 / 68

0 0

Enter code

Use the

button to enter the first

number.

Confirm your selection of this number
by pressing the

button.

Now enter the second number.

Repeat the process until all three
numbers have been entered.

To confirm the code

Yes

0 0 0

Confirm code

Confirm the code with

(

Yes

highlighted).

To correct the code

Press the

button so that

highlighted.

Confirm by pressing the

button.

Enter the correct code.

To change the code

See the "Supervisor level" setting.

Language

You can select the language
displayed via the

Languages

sub-menu.

The flag after the word

Language

acts

as a guide to prevent a language which
will not be understood from being set.

Supervisor level

You can alter the access code to the
supervisor level.

Enter the old code.

Enter a new code.

After you have confirmed the new code,
the display will change to the beginning
of the

Settings

menu.

Settings menu

Содержание PT 5137 WP





































































Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды

Miele PT 5137 WP, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды