Miele PT 5137 WP Скачать руководство пользователя страница 39

Страница: 39 / 68

Bottom right grille/airway

When to clean

The grille should only be

cleaned when

Open bottom right

grille. Clean airways

appears in the

display.

Press

to delete the

Open bottom

right grille. Clean airways

prompt.

Confirm with

Removing

Use the yellow lever supplied to open
the bottom right grille.

Insert the lever in the middle of the
gap at the top and lift it up gently
(see arrow) until the grille opens out
at the top.

Now remove the grille by pulling it
diagonally upwards.

Cleaning

Check whether the cooling fins are
clogged.

Danger of injury.

Do not touch the cooling fins with
your hand. You could cut yourself.

Visible clogging:

We recommend cleaning with a

vacuum cleaner and dusting brush,

Pass the dusting brush over the
cooling fins very lightly and
without using any pressure.

Take care not to bend or damage
the cooling fins.

Remove any soiling with the dusting
brush

carefully

and without using

any pressure.

Cleaning and care

Содержание PT 5137 WP





































































Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды

Miele PT 5137 WP, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды