Miele PT 5137 WP Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 68

background image

Replacing

^

Fit the filter back on the handle. Make
sure it is the correct way round.

To ensure that the filter is positioned
correctly in the front of the heat
exchanger unit:

^

First insert the handle with the filter
attached over the two guide pins.

Make sure that the

yellow dot on

the handle is on the right

.

^

Push the filter in completely.

A programme cannot be started if
the filter is not replaced in the dryer
or is replaced the wrong way round.
A message will appear in the
display.

^

Close the access flap.

,

The filter must be fitted correctly

and the access flap closed to
ensure that water cannot leak from
the condenser system and to ensure
that the dryer functions efficiently.

Cleaning and care

38

«
...
36
37
38
39
40
...
»

Содержание PT 5137 WP





































































Отзывы:

Нет отзывов

Похожие инструкции для PT 5137 WP

Бренд: Gorenje Страницы: 56

HANDY 831 Series

Бренд: VALERA Страницы: 34

Бренд: Frymaster Страницы: 3

Бренд: PITSOS Страницы: 12

Бренд: Haier Страницы: 15

Бренд: Haier Страницы: 16

Бренд: Haier Страницы: 36

Бренд: Haier Страницы: 80

Бренд: Haier Страницы: 90

Бренд: Haier Страницы: 106

Бренд: Haier Страницы: 124

Бренд: Miele Страницы: 100

Бренд: Miele Страницы: 84

Бренд: Miele Страницы: 84

Бренд: Miele Страницы: 1

Бренд: LAVATHERM Страницы: 28

Бренд: contoure Страницы: 30

Бренд: Fisher & Paykel Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды