Miele PT 5137 WP Скачать руководство пользователя страница 31

Страница: 31 / 68

Payment system

Credit may be lost if, after the
programme has started, the door is
opened or the programme cancelled
(depending on how the machine
was set up*).

* A Miele service technician can re-set
the payment system so that
programming changes can be made
within a specified time period.

Changing a programme once it
has started

You cannot change to another
programme once a programme has
started (this prevents unintentional
alterations). If the programme selector
is altered, the words

Programme

cannot be changed

appear if the

selector is not turned back to the
original programme.

You will need to cancel the current
programme before you can select a
new one.

Cancelling the current
programme

Turn the programme selector to

Finish

When

Finish

appears in the display,

this shows that the programme has
been cancelled.

Open the door.

Close the door.

Select a new programme.

Press the

Start

button.

Adding or removing laundry
after a programme has started

Press the

Door

button.

Open the door.

Add or remove items as required.

Close the door.

Press the

Start

button.

Power cut

– If the dryer is switched off during a

drying programme or there has been
a power cut:

When the power is restored and/or
the dryer is switched on again,
confirm with

and start the

programme again.

Time remaining

The time left shown in the display may
now vary from the actual drying time.

Changing the programme sequence

Содержание PT 5137 WP





































































Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды

Miele PT 5137 WP, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды