Miele PT 5137 WP Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 68

background image

Cleaning the plinth filter

When to clean

Normal operation of the dryer

The plinth filter should be cleaned
when the

Clean plinth filter

prompt

appears in the display.

^

Press

OK

to delete the

Clean plinth

filter

prompt. Confirm with

OK

.

Continuous operation of the dryer

The plinth filter should be cleaned
once a day and also when the
prompt to do so appears in the
display.

Removing and disassembling

^

To open, press the right hand side of
the plinth filter access panel.

The panel will spring open.

^

Pull the filter out by the handle.

^

Pull the handle out of the filter.

Cleaning and care

36

«
...
34
35
36
37
38
...
»

Содержание PT 5137 WP





































































Отзывы:

Нет отзывов

Похожие инструкции для PT 5137 WP

Бренд: Fantech Страницы: 4

Бренд: Blomberg Страницы: 44

Бренд: Baron Страницы: 109

Бренд: Jata electro Страницы: 24

Бренд: Magic Chef Страницы: 42

Бренд: EXALTA Страницы: 52

Бренд: CombiSteel Страницы: 31

Бренд: Maguire Products Страницы: 92

Бренд: Bosch Страницы: 40

Бренд: Bosch Страницы: 40

Бренд: LG Страницы: 36

Бренд: LG Страницы: 62

Бренд: Barton Страницы: 12

Pocket Hardmount

Бренд: Alliance Laundry Systems Страницы: 22

Бренд: Alliance Laundry Systems Страницы: 136

Бренд: VALERA Страницы: 46

Бренд: Midea Страницы: 56

Бренд: AIRFLO Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды