Miele PT 5137 WP Скачать руководство пользователя страница 23

Страница: 23 / 68

Select a programme

Press the

On/Off

button

briefly to

switch on.

Please note:

– If no further selection is made within

15 minutes, the dryer will switch off
automatically.

– This does not apply to machines with

a payment system.

Turn the selector to the programme
you require.

The display will vary according to which
programme has been selected.

With the

Cottons

and

Minimum iron

programmes, the drying level is
selected with the programme selector.

To select a Special programme

A selection of programmes will appear
in the display when you select

Special

programmes

Denim

Shirts

Outerwear

Use the

button to highlight the

programme you want. The arrow

in the display indicates that there are
further options.

Confirm your selection by pressing
the

button.

On some Special programmes, the
drying level can be altered as follows:

Shirts

Normal

Duration:

0:36

Use the

button to change the

drying level.

For the drying level options, see
"Programme chart".

Warm air, Cool air and Basket
programmes

1:00

Warm air

Duration:

1:00

The programme duration can be
increased or reduced using the

–

buttons.

Short instructions

Содержание PT 5137 WP





































































Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды

Miele PT 5137 WP, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды