Miele PT 5137 WP Скачать руководство пользователя страница 46

Страница: 46 / 68

Problem

Possible cause

Remedy

The programme does
not start and the display
is dark.

No obvious cause.

– Is the dryer switched

on?

– Is the door closed

properly?

– Has the fuse or circuit

breaker tripped?

When the power comes
back on after a power
cut, confirm with

and

start the programme
again.

The dryer switches off
automatically after 15
minutes if no further
selection is made.

Switch the dryer on.

The display is in a
different language.

A different language has
been selected in "Settings

" "Language

Set the language you
want. The flag symbol
will guide you.

The indicator lamp for
the Start button flashes
when a programme is
being selected.

This is not a fault.

The flashing indicates
that a programme can be
started.

Once the programme has
been started, the

Start

button stops flashing and
lights up constantly.

The display is dark and
the light ring around the
multi-function selector
is not lit up.
The Start button light
flashes slowly.

The display has switched
off automatically to save
energy (Standby mode).

The same applies to the
programme selector.

The display and
programme selector are
lit up after pressing a
button or turning the
programme selector.

The programme selector
light goes out when the

Settings

menu has been

selected.

The programme selector
light comes on when a
programme is selected.

If the problem persists,
there is a fault.

Contact the Miele Service
Department.

Problem solving guide

Содержание PT 5137 WP





































































Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды

Miele PT 5137 WP, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды