Miele PT 5137 WP Скачать руководство пользователя страница 19

Страница: 19 / 68

Ensure that the dryer is installed

and connected to the electricity
supply correctly. If the tumble dryer
has not been transported as
described in "Installation and
connection" then it must be left to
stand for at least 1 hour before it is
connected to the electricity supply.

Press the

On/Off

button

briefly to

switch on.

As soon as the dryer is ready to use,
the Entry menu appears.

When the tumble dryer is switched on
for the first time, the

Miele Professional

welcome

screen will appear.

The display for setting the language will
then appear.

Setting the language

dansk

deutsch

english

Use the

and

–

buttons to select the

language you want, and confirm your
choice by pressing the

button.

A tick

will appear beside the

language to show that it has been set.

Setting the time (of day)

(if necessary)

It is possible to alter the time at any
stage via the Settings menu.

: 00

Set the time of day

Set the hour with the

–

and

buttons,

and confirm your selection by
pressing the

button.

Now set the minutes and confirm
your selection.

Entry menu

The Entry menu will always appear after
the dryer has been switched on, until
you select a programme.

10:00

Select a programme

Settings

...

See "Settings menu" at the end of this
booklet for more information.

You can now load the laundry into the
dryer and select a programme as
described in "Short instructions".

Before using for the first time

Содержание PT 5137 WP





































































Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды

Miele PT 5137 WP, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды