Miele PT 5137 WP Скачать руководство пользователя страница 44

Страница: 44 / 68

Other problems

Problem

Possible cause

Remedy

The drying
process goes
on too long or
even switches
off.

Please check all the possible causes and switch the dryer off
and then back on again.

Ventilation to and from the
dryer may be insufficient, e.g.
because it is installed in a
room which is too small. This
can cause the temperature in
the room to rise sharply.

Open a door or window while
the dryer is in operation for
increased air flow.

The cooling fins behind the
bottom right grille are dirty.

Clean these as described in
"Cleaning and care - Bottom
right grille/airway".

Detergent residues, hair and
fine fluff can clog up block the
fluff filters in the door and the
door opening and the plinth
filter.

Clean these as described in
"Cleaning and care - Cleaning
the surfaces of the fluff
filters/Cleaning the plinth
filter".

The fluff filters and the plinth
filter were still wet when they
were replaced.

The fluff filters and the plinth
filter must be dry.

The laundry has not been
spun sufficiently.

Make sure that your laundry is
thoroughly spun at the
appropriate spin speed in the
washing machine.

The tumble dryer has been
overloaded.

Do not exceed the maximum
load for the programme
selected.

Metallic components, e.g. zips
have prevented the dryer from
registering the correct
moisture level in the laundry.

– Open zips next time.

If the problem occurs again,
dry garments with long zips
using the

Warm air

programme (timed drying).

Problem solving guide

Содержание PT 5137 WP





































































Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды

Miele PT 5137 WP, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды