Miele PT 5137 WP Скачать руководство пользователя страница 60

Страница: 60 / 68

Opening the Settings menu

If the

Settings

menu is not locked,

some of the settings may be
changed.

The entry menu showing the current
time of day will appear after the dryer
has been switched on, until you
select a programme.

10:00

Select a programme

Settings

...

Press the

button.

This will take you into the

Settings

menu.

Selecting a setting

Back

Language

Supervisor level

Use the

and

–

buttons to select the

setting you want, and confirm your
selection by pressing the

button.

– The arrow

in the display indicates

that there are further options.

– If you do not make a selection in the

Settings

menu and in its sub-menus

within approx. 15 seconds, the
display will revert to the previous
menu.

Closing the Settings menu

Back

Language

Supervisor level

Select

Back

and confirm your

selection with the

button.

Opening the Settings menu via
the Supervisor level

The

Settings

menu can be locked

against unauthorised use (except for
the Language option

). It will then

only be able to be accessed at
Supervisor level by entering a code.

Back

Language

Supervisor level

Open the

Supervisor level

sub-menu

To enter the code

Back

Access via code

Change code

Confirm

Access via code

Enter the code

0 0 0

(factory default

setting). If you enter the code wrongly
three times, you will be locked out of
the Supervisor level for an hour.

Settings menu

Содержание PT 5137 WP





































































Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды

Miele PT 5137 WP, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание PT 5137 WP

Отзывы:

Похожие инструкции для PT 5137 WP

Бренды по названию

Популярные бренды