Miele PT 5137 WP Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 68

background image

This tumble dryer has a multi-stage
filter system consisting of the

fluff

filter in the door, the fluff filters in
the door opening (1.)

and a

plinth

filter (2.)

.

This system, including the

grille in

the bottom right/airway (3.)

,

requires maintenance.

Make sure you clean all the
filters at the correct intervals

– This dryer must not be used

without the fluff filters or the plinth
filter in place.
The grille in the bottom right must
always be in place.

– Make sure that the fluff filters and

the plinth filter are not damaged.
Replace them immediately, if they
are damaged in any way.

,

If the above instructions are not

observed, an excessive build-up of
fluff can occur which in turn can
cause a fault.

1. When to clean the surfaces of the
fluff filters

Clean the surfaces of the fluff filters
after each drying programme.

The fluff filters located in the door
and the door opening collect fluff
from items being dried.

^

See "Cleaning the surfaces of the fluff
filters".

Cleaning and care

32

«
...
30
31
32
33
34
...
»

Содержание PT 5137 WP





































































Отзывы:

Нет отзывов

Похожие инструкции для PT 5137 WP

Professional 1 Slim

Бренд: Taurus Страницы: 44

Professional 1 Slim

Бренд: Taurus Страницы: 60

STUDIO 2400 IONIC

Бренд: Taurus Страницы: 36

Бренд: Maytag Страницы: 20

Бренд: Gaggenau Страницы: 18

Бренд: Maytag Страницы: 188

Бренд: Logik Страницы: 28

Бренд: Parker Страницы: 38

Бренд: INVENTOR Страницы: 64

Бренд: GE Страницы: 60

Бренд: Asko Страницы: 32

Бренд: Easy@Home Страницы: 39

Бренд: Modena Страницы: 20

Бренд: Frigidaire Страницы: 6

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 3

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды