Metro Therm SHK 200S, Инструкция по установке и эксплуатации

Страница: 14 / 80

14 SHK 200S
SHK 200S-6
Pipe dimensions and materials
SHK 200S Gas pipe Liquid pipe
Pipe replacement Ø15,88 mm (5/8”) Ø9,52 mm (3/8”)
Connection Connection – (5/8") Connection – (3/8”)
Material
Quality of copper SS-EN 12735-1 or
C1220T, JIS H3300
Minimum ma -
terial thickness
1,0 mm 0,8 mm
External diam-
eter, copper
pipe (mm)
B, using
R410A (mm)
B, using a
conventional
tool (mm)
Ø 9,52
0,0~0,5
0,7~1,3
Ø 15,88
Ø 6,35
1,0~1,5
Ø 12,7
External
diameter,
copper
pipe (mm)
Torque
(Nm)
Tightening
angle
(°)
Recom -
mended
tool length
(mm)
Ø6,35 14~18 45~60 100
Ø 9,52 34~42 30~45 200
Ø12,7 49~61 30~45 250
Ø 15,88 68~82 15~20 300
Pipe connection
• Execute the pipe installation with the mainte-
nance valves (QM35, QM36) closed.
METROAIR L6 / METROAIR L8
• Remove the side panel on METROAIR L during
the installation to make access easier.
Socket connections
Extension:
Shift:
METROAIR L12
• Remove the “to be removed” part from the exter -
nal panel at the METROAIR L mode where pipes
are to be led. The drawing below presents exem-
plary pipe outlets.
• Make sure that no water or dirt can permeate to the
pipes. Contamination of the pipes may damage
the heat pump.
A
B
Vacuum
pump
Serviceventil, gas
Mätuttag
Manometer
Serviceventil, vätska
Zawór serwisowy,
ciecz
Zawór serwisowy,
gaz
Wyjście pomiarowe
Manometr
Pompa
próżniowa
A
B
Vacuum
pump
Serviceventil, gas
Mätuttag
Manometer
Serviceventil, vätska
Zawór serwisowy,
ciecz
Zawór serwisowy,
gaz
Wyjście pomiarowe
Manometr
Pompa
próżniowa
A
B
Vacuum
pump
Serviceventil, gas
Mätuttag
Manometer
Serviceventil, vätska
Zawór serwisowy,
ciecz
Zawór serwisowy,
gaz
Wyjście pomiarowe
Manometr
Pompa
próżniowa
IMPORTANT
When soldering, apply the shielding gas.
External diameter,
copper pipe
A (mm)
Ø 6,35 9,1
Ø 9,52 13,2
Ø 12,7 16,6
Ø 15,88 19,7
SHK 200S
SHK 200S-6
• Bend pipes with maximum bending radius (at
least R100~R150). Do not bend pipes many
times. Use a bending machine.
• Connect the socket connection and tighten with
appropriate torque. Apply the appropriate tight-
ening angle if the torque wrench is not available.
SHK 200S-6 Gas pipe Liquid pipe
Pipe replace-
ment
Ø12,7 mm (1/2”) Ø6,35 mm (1/4”)
Connection Connection – (1/2") Connection – (1/4”)
Material
Quality of copper SS-EN 12735-1 or
C1220T, JIS H3300
Minimum ma -
terial thickness
1,0 mm 0,8 mm
Front
Elements to be removed
Chapter 4 | Pipe connections