Metal-Fach Z562 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 52

Metal-Fach Z562 Скачать руководство пользователя страница 32

32

INSTRUCTION MANUAL

– BALER Z562

4.14 Adjusting The Lock

To adjust the lock (Section 44), loosen the jam nut (2). Use the adjusting nut (1) to set

the length A which is from 0 mm to 2 mm. Tighten the jam nut (2). Loosen the jam nut of the

adjustment screw (3) located on the right-hand side of the baler. Use the adjusting screw (3)

to set the length B which is from 2 mm to 5 mm. Check that the adjusted lock works properly.

Turn on the hydraulic system by feeding fluid to the actuators, which open the rear hatch, until

the starting moment of opening it. At that moment, stop feeding the fluid, leave the tractor cab

and make sure that the opening hatch will not cause a collision between the hook (4) and the

bushing (5). If such a collision is found, close the hatch and repeat the adjustment to remove it.

Figure 44.

Lock adjustment

WARNING!

During the cover-stop-valve adjustment, follow the H&S guidelines. Use
the cover-stop valve only to adjust the speed of the cover closing.

WARNING

«
...
30
31
32
33
34
...
»

Содержание Z562





















































Отзывы:

Нет отзывов