Metal-Fach Z562 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 52

Metal-Fach Z562 Скачать руководство пользователя страница 11

INSTRUCTION MANUAL

– BALER Z562

11

a flashing red dot “8.8.8

.

8.” Simultaneously, press and hold

“Deleting”

(red flashing dots

“8.8.8

.

8

.

” are displayed) and

“On/Off” keys

. The following message is displayed “

dEFA

”. After

releasing the keys, the control panel is reset, it enters the work mode in the disabled condition,

and the display shows a flashing

red dot “8.8.8

.

8.”

3.5.6 Zeroing The Workday Counter

Press and hold “

Deleting

” to zero the workday counter.

The key must be kept held down until the

“

0

” digit is displayed.

3.6

Hydraulic Installation

WARNING!

Ensure the fluid purity in the tractor-power hydraulic system. The purity
of the fluid must be compliant with condition 20/18/15 of ISO 4406-1996.

WARNING

WARNING!

Ensure the full working order of the hydraulic system. The fluid which
works under high pressure heats up to a temperature which poses a
threat to health.

WARNING

WARNING!

For replacements it is recommended to use original spare parts that will
assure maintaining the baler in full efficiency for a long time of its
operation.

WARNING

WARNING!

Worn or defective hoses in the power hydraulics must be replaced with
new ones.

WARNING

«
...
9
10
11
12
13
...
»

Содержание Z562





















































Отзывы:

Нет отзывов