Mercury FourStroke 2.5 Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 205

Mercury FourStroke 2.5 Скачать руководство пользователя страница 97

Powerhead

Page 4A-16

90-8M0065421 NOVEMBER 2012

4. Measure the thermostat opening when the specified water temperature is achieved.

a -

Minimum thermostat valve lift

Thermostat Specifications
Start to open temperature

50–54 °C (122–129 °F)

Full open temperature

60–64 °C (140–147 °F)

Minimum thermostat valve lift

2 mm (0.079 in.)

Installation

1. Clean the gasket surfaces on the thermostat housing bracket and cylinder block.
2. Install the thermostat.
3. Install a new thermostat gasket.
4. Install the thermostat housing bracket. Tighten the bolts to the specified torque.
5. Install the M6 x 60 bolt through the recoil starter. Tighten the bolt to the specified torque.

Description

Nm

lb‑in.

lb‑ft

Thermostat housing bracket mounting bolts (3)

6

53

Recoil starter bolts (M6 x 60)

6

53

6. Secure the throttle cables with the J‑clamp.

a

3120

«
...
95
96
97
98
99
...
»

Содержание FourStroke 2.5














































































































































































































Отзывы:

Нет отзывов