Mercury FourStroke 2.5 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 205

Mercury FourStroke 2.5 Скачать руководство пользователя страница 22

Maintenance

90-8M0065421 NOVEMBER 2012

Page 1B-9

NOTE: Replace the sealing washers with new washers.

a -

Vent plug

b -

Fill/drain plug

Gearcase Lubricant Capacity

Gearcase lubricant capacity is approximately 180 ml (6.0 fl oz).

Checking Lubricant Level and Refilling Gearcase

1. Place the outboard in a vertical operating position.
2. Remove vent plug.
3. Remove fill/drain plug. Place lubricant tube into the fill hole and add lubricant until it appears at the vent hole.

a -

Vent plug and new sealing washer

b -

Vent hole

c -

Fill/drain plug and new sealing washer

Tube Ref No.

Description

Where Used

Part No.

82

Premium Gear Lubricant

Gearcase

92-858058K01

4. Stop adding lubricant. Use new sealing washer and install the vent plug before removing the lubricant tube.
5. Remove lubricant tube and reinstall cleaned fill/drain plug and new sealing washer.

Lubrication Points

Lubricate the following with Quicksilver or Mercury Precision Lubricants 2‑4‑C with PTFE or Special Lubricant 101.

Tube Ref No.

Description

Where Used

Part No.

95

2-4-C with PTFE

Steering friction knob threads, swivel bracket bushing, tilt

support pin, transom clamp screws

92-802859A 1

34

Special Lubricant 101

Steering friction knob threads, swivel bracket bushing, tilt

support pin, transom clamp screws

92-802865Q02

a

b

19077

b

a

c

19080

«
...
20
21
22
23
24
...
»

Содержание FourStroke 2.5














































































































































































































Отзывы:

Нет отзывов