manualshive.com logo in svg

Mercury FourStroke 2.5, Руководство по обслуживанию, Страница: 167 / 205

Поделиться
Скачать
Mercury FourStroke 2.5 Скачать руководство пользователя страница 167

Gear Housing  

Page 6A-26

90-8M0065421   NOVEMBER  2012

Tube Ref No.

Description

Where Used

Part No.

95

2-4-C with PTFE

Shift shaft surface

92-802859A 1

Forward Gear Backlash

Check forward gear backlash as follows:
•

Apply down pressure on the driveshaft

•

Push up on the pinion gear (gear floats on the driveshaft)

•

Rock the forward gear back and forth

A light clicking sound (0.050–0.152 mm [0.002–0.006 in.]) should be heard. If excessive freeplay exists (over 0.30 mm

[0.012 in.]), the gear housing components should be inspected for wear. If no freeplay exists, either the forward gear or forward

gear bearing are not seated properly in the gear housing or the lower driveshaft bearing (above the pinion gear) is positioned

too low in the driveshaft housing.

Propeller Shaft

NOTE: Verify the shift cam is aligned properly in the gear housing.

Install the propeller shaft assembly into the forward gear/bearing assembly.

a -

Propeller shaft

Bearing Carrier

Slide the bearing carrier assembly over the propeller shaft. Secure the carrier to the gear housing with two bolts and flat

washers. Tighten the bolts to the specified torque.

a -

Carrier

b -

Bolts and washers

Description

Nm

lb‑in.

lb‑ft

Bolts with washers

5.6

50

a 

a

25641

a

b

25646

Содержание FourStroke 2.5














































































































































































































Отзывы:

Нет отзывов