manualshive.com logo in svg

Mercury FourStroke 2.5, Руководство по обслуживанию, Страница: 107 / 205

Поделиться
Скачать
Mercury FourStroke 2.5 Скачать руководство пользователя страница 107

Powerhead  

Page 4A-26

90-8M0065421   NOVEMBER  2012

Piston
   Outside diameter (standard)

54.96 mm (2.1638 in.)

   Outside diameter (service limit)

54.90 mm (2.1614 in.)

   Clearance (standard)

0.02–0.06 mm (0.00078–0.00236 in.)

   Clearance (service limit)

0.15 mm (0.0059 in.)

3. To determine a piston to cylinder wall clearance, use this formula:

•

Minimum cylinder bore measurement – maximum piston diameter measurement = piston to cylinder wall clearance.

Piston Pin

1. Measure the piston pin.

3132

Piston Pin
   Inside diameter (standard)

14.0 mm (0.5512 in.)

   Inside diameter (service)

13.97 mm (0.550 in.)

2. Place the piston pin into the connecting rod and check for free play. There should be no noticeable free play. Replace the

pin and/or the connecting rod as necessary.

3133

3. Place the piston pin into the piston and check for free play. There should be no noticeable free play. Replace the pin and/or

the piston as necessary.

3134

Содержание FourStroke 2.5














































































































































































































Отзывы:

Нет отзывов