manualshive.com logo in svg

Mercury FourStroke 2.5, Руководство по обслуживанию, Страница: 139 / 205

Поделиться
Скачать
Mercury FourStroke 2.5 Скачать руководство пользователя страница 139

Clamp/Swivel Bracket and Driveshaft Housing  

Page 5A-14

90-8M0065421   NOVEMBER  2012

Steering Stop Components

a -

Stopper and pin

b -

Steering stop lever

c -

Bolt and washer

d -

Spring ends

e -

Swivel bracket

Installation

1. Lubricate the driveshaft housing between the upper and lower flanges with 2‑4‑C with PTFE.
2. Install the thrust plate and split plastic bushing onto the driveshaft housing.

NOTE: Install the split plastic bushing with the split facing towards the front of the engine.

3. Lubricate the thrust plate and plastic bushing with 2‑4‑C with PTFE.

a -

Thrust plate

b -

Plastic bushing

c -

Split in plastic bushing

d -

Lower flange

e -

Driveshaft housing

f -

Upper flange

Tube Ref No.

Description

Where Used

Part No.

95

2-4-C with PTFE

Driveshaft housing between flanges, swivel bracket thrust

plate, and plastic bushing

92-802859A 1

4. Align the tab on the rubber bushing with the pocket of the swivel bracket. Install the rubber bushing onto the swivel bracket.

NOTE: It is not necessary to use adhesive to attach the rubber bushing onto the front swivel bracket.

a

26145

e

b

b

c

d

d

26155

a

b

c

d

e

f

Содержание FourStroke 2.5














































































































































































































Отзывы:

Нет отзывов