Mercury FourStroke 2.5 Скачать руководство пользователя страница 52

Страница: 52 / 205

Ignition

90-8M0065421 NOVEMBER 2012

Page 2A-11

11. Apply Loctite 242 Threadlocker to the three fuel tank mounting bolts. Install the bolts and washers. Tighten the bolts to the

specified torque.

a -

Fuel tank

b -

Bolt and washer (M6 x 25) (3)

Tube Ref No.

Description

Where Used

Part No.

Loctite 242 Threadlocker

Fuel tank mounting bolts

92-809821

Description

lb‑in.

lb‑ft

Fuel tank mounting bolt (M6 x 25) (3)

12. Secure the fuel line hose to the fuel tank with a hose clamp.

Ignition Coil Testing

Secondary Resistance

NOTE: The readings listed are taken at 20 °C (68 °F) with a digital ohmmeter. Due to the number of different manufacturers,

meters available, and temperature variance; test results may vary.
NOTE: It is not necessary to remove the ignition coil from the powerhead for testing.

1. Remove the spark plug cap from the spark plug.
2. Measure the resistance between the spark plug lead and engine ground.

a -

DMT 2004 digital multimeter

b -

Spark plug cap/lead

c -

Black ground wire

DMT 2004 Digital Multimeter

91‑892647A01

50010

41651

Содержание FourStroke 2.5














































































































































































































Результаты поиска

Содержание FourStroke 2.5

Отзывы:

Mercury FourStroke 2.5, Руководство по обслуживанию, Страница: 52 / 205

Результаты поиска

Содержание FourStroke 2.5

Отзывы: