manualshive.com logo in svg

Mercury FourStroke 2.5, Руководство по обслуживанию, Страница: 140 / 205

Поделиться
Скачать
Mercury FourStroke 2.5 Скачать руководство пользователя страница 140

  Clamp/Swivel Bracket and Driveshaft Housing

90-8M0065421   NOVEMBER  2012

Page 5A-15

5. Lubricate the inside of the rubber bushing with 2‑4‑C with PTFE.

a -

Rubber bushing

b -

Swivel bracket

Tube Ref No.

Description

Where Used

Part No.

95

2-4-C with PTFE

Swivel bracket rubber bushing

92-802859A 1

6. Install the swivel bracket with the rubber bushing onto the driveshaft housing.

a -

Thrust plate

b -

Rubber bushing

c -

Split plastic bushing

d -

Tab

e -

Swivel bracket

7. Attach the swivel bracket cap to the swivel bracket.

NOTE: The split plastic bushing tabs fit into the cast pockets of the swivel bracket cap.

8. Apply Loctite 271 Threadlocker to the four special flange head bolt threads. Install the bolts. Tighten the bolts to the

specified torque.

IMPORTANT: Do not use common bolts to secure the swivel bracket/swivel bracket cap.

a -

Special bolt and washer (4) (M6 x 35)

b -

Swivel bracket cap

c -

Swivel bracket

26157

a

b

26140

a

b

c

e

d

26138

a

b

c

Содержание FourStroke 2.5














































































































































































































Отзывы:

Нет отзывов