Mercury FourStroke 2.5 Скачать руководство пользователя страница 166

Страница: 166 / 205

Gear Housing

90-8M0065421 NOVEMBER 2012

Page 6A-25

3. Press the new ball bearing (number side up) into the carrier until the bearing seats. Use a press with a driver and mandrel

from the bearing removal and installation kit.

a -

Bearing

b -

Mandrel (37312)

Tube Ref No.

Description

Where Used

Part No.

2-4-C with PTFE

Outside diameter of carrier bearing

92-802859A 1

Bearing Removal and Installation Kit

91‑31229A7

4. Install the carrier O‑ring. Apply 2‑4‑C with PTFE to the O‑ring surface.

a -

O‑ring

Tube Ref No.

Description

Where Used

Part No.

2-4-C with PTFE

Bearing carrier O-ring surface

92-802859A 1

Shift Shaft

1. Install the shift shaft into the gear housing. Apply a light coat of 2‑4‑C with PTFE on the shift shaft to lubricate the O‑ring in

the water pump base.

2. Install the water pump base and a new base gasket.

a -

Shift shaft

b -

Pump base

c -

Base gasket

25639

25554

25640

Содержание FourStroke 2.5














































































































































































































Результаты поиска

Содержание FourStroke 2.5

Отзывы:

Mercury FourStroke 2.5, Руководство по обслуживанию, Страница: 166 / 205

Результаты поиска

Содержание FourStroke 2.5

Отзывы: