Mercury FourStroke 2.5 Скачать руководство пользователя страница 65

Страница: 65 / 205

Carburetor and Fuel Pump

Page 3A-12

90-8M0065421 NOVEMBER 2012

8. Disconnect the choke cable and the throttle linkage from the carburetor. Remove the carburetor from the engine.

a -

Crankcase breather hose

b -

Throttle linkage

c -

Vent hose (1 of 2)

d -

Choke cable

e -

Carburetor/air silencer bolt (M6 x 85) (2)

Installation

1. Connect the choke cable and the throttle linkage to the carburetor.

IMPORTANT: The carburetor mounting gaskets must be oriented correctly with the intake manifold before installing the

carburetor. Improper orientation of the carburetor mounting gaskets will result in poor engine performance.

a -

Orientation notch

2. Inspect the carburetor mounting gaskets for damage. Replace the gaskets as required.

41668

Содержание FourStroke 2.5














































































































































































































Результаты поиска

Содержание FourStroke 2.5

Отзывы:

Mercury FourStroke 2.5, Руководство по обслуживанию, Страница: 65 / 205

Результаты поиска

Содержание FourStroke 2.5

Отзывы: