manualshive.com logo in svg

Mercury FourStroke 2.5, Руководство по обслуживанию, Страница: 190 / 205

Поделиться
Скачать
Mercury FourStroke 2.5 Скачать руководство пользователя страница 190

  Tiller Handle

90-8M0065421   NOVEMBER  2012

Page 7B-9

9. Adjust the friction knob to the desired setting.

a -

Tiller handle grip screw

b -

Grip

c -

Friction knob

d -

Throttle shaft bracket screw

e -

Throttle shaft bracket

Tiller Handle Installation

1. Install the tiller handle and steering bracket into the opening in the bottom cowl. Secure the tiller handle to the bottom cowl

with two bolts and washers. Tighten the bolts to the specified torque.

a -

Tiller handle mounting bolt and washer (M8 x

35) (2)

b -

Steering bracket

Description

Nm

lb‑in.

lb‑ft

Steering bracket mounting bolt (M8 x 35) (2)

15

132

2. Install the throttle cable ends into the slots in the throttle drum.

IMPORTANT: Throttle cable "B" is pulled in the direction of the arrow when the grip is rotated from the "START" position to

the full throttle position.

NOTE: Loosen the throttle drum bolt slightly to aid in the installation of the throttle cable ends. Tighten the bolt to the

specified torque.

26044

a

c

b

d

e

26018

a

b

Содержание FourStroke 2.5














































































































































































































Отзывы:

Нет отзывов