Mercury FourStroke 2.5 Скачать руководство пользователя страница 152

Страница: 152 / 205

Gear Housing

90-8M0065421 NOVEMBER 2012

Page 6A-11

3. Note the color of the gear lubricant. White or cream color indicates the presence of water in the lubricant. Check the drain

pan for water separation from the lubricant. The presence of water in the gear lubricant indicates the need for disassembly

and inspection of the oil seals, seal surfaces, O‑rings, and gear housing components. Pressure check the gearcase prior to

disassembly and again after reassembly to verify repairs have been properly completed.

a -

Oil level screw with gasket

b -

Oil fill screw with gasket

Propeller Removal

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the water with a propeller installed.

Before installing or removing a propeller, place the drive unit in neutral and engage the lanyard stop switch to prevent the

engine from starting. Place a block of wood between the propeller blade and the anti‑ventilation plate.

1. Remove the cotter pin and pull the propeller off of the propeller shaft.
2. Remove the drive (shear) pin.

a -

Cotter pin

b -

Drive (shear) pin

Gear Housing Removal

1. Close the fuel shut‑off valve.

OIL LEVEL

OIL

25501

25519

Содержание FourStroke 2.5














































































































































































































Результаты поиска

Содержание FourStroke 2.5

Отзывы:

Mercury FourStroke 2.5, Руководство по обслуживанию, Страница: 152 / 205

Результаты поиска

Содержание FourStroke 2.5

Отзывы: