Mercury FourStroke 2.5 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 205

Mercury FourStroke 2.5 Скачать руководство пользователя страница 61

Carburetor and Fuel Pump

Page 3A-8

90-8M0065421 NOVEMBER 2012

Carburetor Adjustments

Pilot (Idle Mixture) Screw

IMPORTANT: The pilot mixture screw is set at the factory to allow the engine to meet established government emission

specifications. The pilot mixture screw is normally hidden with a tamperproof plug. However, if the carburetor requires

rebuilding and/or cleaning, the plug can be removed and the pilot mixture screw removed to facilitate cleaning. Follow the

procedure below when the carburetor is rebuilt or cleaned.
1. When removing: Record the number of revolutions to lightly seat the pilot mixture screw.
2. When installing: Turn the pilot mixture screw in (clockwise) until lightly seated. Then back the screw out the same number

of turns as measured during removal.

3. After installation, install a new tamperproof plug.

a -

Pilot mixture screw (tamperproof plug removed)

Idle Speed

After the pilot (idle mixture) screw has been properly installed, adjust the idle speed screw to specification.
•

Tightening the screw increases the engine speed.

•

Loosening the screw reduces the engine speed.

Engine RPM (2.5/3.5)
Idle speed (neutral)

1400 ± 50 RPM

Idle speed (forward)

1300 ± 50 RPM

a -

Idle speed screw

a

26506

a

26509

«
...
59
60
61
62
63
...
»

Содержание FourStroke 2.5














































































































































































































Отзывы:

Нет отзывов