background image

 

Technical Manual Presence Detector SCN-P/G360XX.02 

 

 

 

MDT technologies GmbH  •  

51766 Engelskirchen  •  Papiermühle 1

 

 

Tel.: +49-2263-

880  •

  Fax: +49-2263-4588  

• knx@mdt.de  •  www.mdt.de

 

8

 

 

8

2.5 Functions 

 
The functions of the presence detector are divided in the areas general settings, settings for the light 
control, the sending behavior and the calibration for the brightness value, settings for logic, 
activation of LED, settings for scenes and, according to the the hardware type, the constant light 
control. 
The following menus are shown and can be parametrized further: 

 

General setting 

The general settings are used for basic configuration of the presence detector. Here, the 
usage of the day/night object (separate switching objects for day/night), basic settings of 
sensitivity and brightness, forced control as well as release of external push-button input are 
set. 
 

 

Channel selection 

Up to four light groups, one HCV and one alarm group can be activated here. 

o

 

Light groups 1/2/3/4   

(Only 3 light groups possible for models with only 3 sensors). 

Settings for presence operation can be made here. In this menu, active sensors, the 
operating mode of the detector, forced control or lock object, the sending conditions, 
the follow-up time and external push-button inputs can be defined. 

 

o

 

HCV

 

The Heating-, Ventilation-, Climate-channel is the interface of the presence detector 
to other subsections. In contrast to the light channels, the HCV channel has 
adjustable observation windows with which the presence in the room can be 
monitored. By using this channel you can, for example, control the ventilation of a 
room as required or switch other HCV functions in presence/absence. 

 

o

 

Alarm 

The alarm channel is used to recognize and detect movements during absence. For 
this purpose, the channel has a separate sensitivity setting and its own enable/lock 
object with which monitoring can be started. Like the HCV channel, the alarm 
channel also provides adjustable observation windows. 

 

 

LED 

Here you can set whether and for which light channel the green LED is active 

 

 

Scenes 

Up to 8 scenes with different settings for light channels 1-4 can be activated here

 

 

 

Brightness 

Settings for the sending of the measured brightness value and a treshold value can be 
adjusted here. 
 

 

Calibration of brightness value 

The correction of the measured brightness value can be adjusted by a steady parameter or 
via the Teach-In object. 

 

 

Содержание SCN-G360D3.02


























































Отзывы: