McQuay RVSS14 страница 6 Скачать руководство пользователя | Manualshive

Страница: 6 / 66

background image

6

IOMM

Starter

Table 1, Starter/VFD Mounting Arrangements

Size

Factory-

Mounted

Free-

Standing

Brackets &

Cables

WSC/WDC 050

X

X

WSC/WDC 063

X

X

WSC/WDC 079

X

X

WSC/WDC 087

X

X

WSC 100 - 126

X

X

WDC 100 - 126

X

WCC 100 - 126

X

Receiving and Setting

Since factory-mounted starters are mounted and wired at the factory, this section will only
apply to free-standing units.

The unit should be inspected immediately after receipt for possible damage.

All McQuay centrifugal starters are shipped FOB factory and all claims for handling and
shipping damage are the responsibility of the consignee.

Extreme care must be used when rigging the starter to prevent damage. See the certified
dimension drawings included in the job submittal for the center of gravity of the unit.
Consult the local McQuay sales office for assistance if the drawings are not available.

The starter can be lifted by fastening the rigging hooks to the four lifting eyes located on the
top of the unit.

Location and Mounting

Clearance

The starter must be mounted on a level concrete or steel base and must be located to provide
adequate service. Local codes or the National Electric Code (NEC) can require more
clearance in and around electrical components and must be checked.

Mounting

Make sure that the floor or structural support is adequate to support the full weight of the
unit.

Standard NEMA 1 and NEMA 12 starters must be installed indoors in an area that is not
exposed to direct water spray. Do not install in areas where the ambient temperature falls
below 32

°

F (0

°

C) or exceeds 104

°

F (40

°

C) enclosed, or 122

°

F (50

°

C) open unless this was

noted at the time of order placement and special precautions were taken to protect against
these abnormal temperatures.

Heatsink temperatures can run as high as 158

°

F (70

°

C) during normal operation. Do not

mount the starter in contact with any material that cannot accept this heat. The starter must be
mounted with the heat sink fins oriented vertically in an area that will not experience
excessive shock or vibration.

Ventilation Requirements

Provisions should be provided in the starter enclosure to ensure that the temperature inside
the enclosure never rises above 122

°

F (50

°

C) or the starter could be damaged or the life of

the starter could be reduced. As a general rule of thumb the following ventilation guidelines
should be followed. These values are for starters with bypass. Bypassed starters generally
do not require ventilation.

«
...
4
5
6
7
8
...
»

Содержание RVSS14



































































Отзывы:

Нет отзывов

Похожие инструкции для RVSS14

Бренд: Bang & Olufsen Страницы: 9

Бренд: Bang & Olufsen Страницы: 12

Бренд: Hach Страницы: 86

Бренд: UniKey Страницы: 20

Бренд: Daikin Страницы: 5

Бренд: Danfoss Страницы: 7

ServeRAID-MR10is

Бренд: IBM Страницы: 94

ServeRAID-4 Ultra160 Series

Бренд: IBM Страницы: 20

8271 Nways Ethernet LAN Switch

Бренд: IBM Страницы: 6

Бренд: IBM Страницы: 86

Бренд: IBM Страницы: 205

Бренд: IBM Страницы: 28

BT300 BurnerTronic

Бренд: Lamtec Страницы: 48

Бренд: EasySMX Страницы: 11

Бренд: EasySMX Страницы: 8

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 426

Бренд: YASKAWA Страницы: 26

Бренд: YASKAWA Страницы: 210

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды