McQuay RVSS14 Скачать руководство пользователя страница 51

Страница: 51 / 66

IOMM Starter

Other Situations

Condition Cause Solution

If input phasing correct, exchange

any two output wires.

Motor Rotates in Wrong Direction Phasing

incorrect

If input phasing incorrect, exchange

any two input wires.

Erratic Operation

Loose connections

Shut off all power and check all

connections.

Motor overloaded

Reduce motor load.

Too many starts per hour

Allow for adequate motor cooling

between starts. Set Hot/Cold ratio

higher or lengthen cooling time.

High ambient temperature

Reduce ambient temperature or

provide for better cooling. Set OL

class lower to compensate for

ambient temperature.

Acceleration time too long

Reduce starting load and/or review

acceleration ramp settings.

Incorrect motor OL settings

Review and correct if necessary

motor OL settings.

Motor Overheats

Motor cooling obstructed/damaged

Remove cooling air obstructions.

Check motor cooling fan.

Fan power supply lost

Verify fan power supply, check fuses.

Fan wiring problem

Check fan wiring.

Starter cooling fans do not operate

(When Present)

Fan failure

Replace fan

Voltage/Current output jumper (JP1)

not set correctly.

Set jumper to give correct output.

Wiring problem

Verify output wiring.

Analog Output Function parameter

(I/O 12, P50) set incorrectly.

Verify that the Analog Output

Function parameter is set correctly.

Analog Output Offset and/or Span

parameters (I/O 13-14, P51-52) set

incorrectly.

Verify that the Analog Output Span

and Offset parameters are set

correctly.

Load on analog output too high.

Verify that load on analog output

meets D3 control analog output

specifications.

Ground loop or noise problems.

Verify correct grounding of analog

output connection to prevent noise or

ground loops from affecting output.

Analog Output not functioning

properly

Содержание RVSS14



































































Результаты поиска

Содержание RVSS14

Отзывы:

McQuay RVSS14, Инструкция по установке, эксплуатации и обслуживанию, Страница: 51 / 66

Результаты поиска

Содержание RVSS14

Отзывы: