McQuay RVSS14 Скачать руководство пользователя страница 41

Страница: 41 / 66

IOMM Starter

Code

Description

Detailed Description of Fault / Possible Solutions

Line frequency above 72 Hz was detected.

Verify input line frequency.

If operating on a generator, check generator speed governor for malfunctions.

F13

High Line

Frequency

Line power quality problem / excessive line distortion.

Three-phase power has been detected when the starter is expecting single-phase power.

Verify that input power is single phase.

Verify that single-phase power is connected to the L1 and L2 inputs. Correct wiring if

necessary.

F14

Input power

not single

phase

Verify that the SCR gate wires are properly connected to the D3 control board.

Single-phase power has been detected when the starter is expecting three-phase power.

Verify that input power is three phase. Correct wiring if necessary.

Verify that the SCR gate wires are properly connected to the D3 control board.

F15

Input power

not three

phase

On medium voltage systems, verify wiring of the voltage feedback measurement circuit.

Low voltage below the Undervoltage Trip Level parameter setting (PFN 08, P31) was

detected for longer than the Over/Under Voltage Trip delay time (PFN 09, P32).

Verify that the actual input voltage level is correct.

Verify that the Rated Voltage parameter (FUN 05,

P66

) is set correctly.

Check input supply for open fuses or open connections.

F21

Low Line L1-

On medium voltage systems, verify wiring of the voltage measurement circuit.

Low voltage below the Undervoltage Trip Level parameter setting (PFN 08, P31) was

detected for longer than the Over/Under Voltage Trip delay time (PFN 09, P32).

Verify that the actual input voltage level is correct.

Verify that the Rated Voltage parameter (FUN 05,

P66

) is set correctly.

Check input supply for open fuses or open connections.

F22

Low Line L2-

On medium voltage systems, verify wiring of the voltage feedback measurement circuit.

Low voltage below the Undervoltage Trip Level parameter setting (PFN 08, P31) was

detected for longer than the Over/Under Voltage Trip delay time (PFN 09, P32).

Verify that the actual input voltage level is correct.

Verify that the Rated Voltage parameter (FUN 05,

P66

) is set correctly.

Check input supply for open fuses or open connections.

F23

Low Line L3-

On medium voltage systems, verify wiring of the voltage feedback measurement circuit.

Содержание RVSS14



































































Результаты поиска

Содержание RVSS14

Отзывы:

McQuay RVSS14, Инструкция по установке, эксплуатации и обслуживанию, Страница: 41 / 66

Результаты поиска

Содержание RVSS14

Отзывы: