manualshive.com logo in svg

McQuay RVSS14, Инструкция по установке, эксплуатации и обслуживанию, Страница: 43 / 66

Поделиться
Скачать
McQuay RVSS14 Скачать руководство пользователя страница 43

IOMM Starter 

 

43 

 

Fault 

Code 

Description 

Detailed Description of Fault / Possible Solutions 

During operation, the D3 controller detected a very high level of current in one or more 

phases. 

Check motor wiring for short circuits or ground faults. 

Check motor for short circuits or ground faults. 

Check if power factor or surge capacitors are installed on the motor side of the starter. 

F30 

I.O.C. 

(Instantaneous 

Overcurrent 

Current) 

Verify that the motor FLA (QST 01, P1), CT ratio (FUN 03, P68), and burden switch 

settings are correct. 

Motor current exceeded the Over Current Trip Level setting (PFN 01, P24) for longer 

than the Over Current Trip Delay Time setting (PFN 02, P25). 

F31 Overcurrent 

 

Check motor for a jammed or an overload condition. 

Motor current dropped under the Under Current Trip Level setting (PFN 03, P26) for 

longer than the Under Current Trip Delay time setting (PFN 04, P27). 

F34 Undercurrent 

 

Check system for cause of under current condition. 

A current imbalance larger than the Current Imbalance Trip Level parameter setting 

(PFN 05, P28) was present for longer than ten (10) seconds. 

Check motor wiring for cause of imbalance. (Verify dual voltage and 6 lead motors for 

correct wiring configuration). 

Check for large input voltage imbalances that can result in large current imbalances. 

F37 

Current 

Imbalance 

Check motor for internal problems. 

Ground current above the Ground Fault Trip level setting (PFN 06, P29) has been 

detected for longer than 3 seconds. 

Check motor wiring for ground faults. 

Check motor for ground faults. 

Megger motor and cabling (disconnect from starter before testing). 

Verify that the motor FLA (QST 01, P1), CT ratio (FUN 03, P68), and burden switch 

settings are correct. 

Verify that the CTs are installed with all the White dots towards the input line. 

F38 Ground 

Fault 

 

Motor current went below 10% of FLA while the starter was running. 

Verify Motor Connections. 

Verify the CT wiring to the D3 control board. 

F39 

No Current at 

Run 

Verify that the motor FLA (QST 01, P1), CT ratio (FUN 03, P68), and burden switch 

settings are correct. 

Содержание RVSS14



































































Отзывы:

Нет отзывов