McQuay RVSS14 Скачать руководство пользователя страница 57

Страница: 57 / 66

IOMM Starter

Default

The default value for the overload parameter is 10.

Phase Order

Description

The line phasing parameter sets the phase sensitivity of the starter. This can be used to protect
the motor from a possible change in the incoming phase sequence. If the incoming phase
sequence does not match the set phase rotation, the starter will display

phs err

while stopped

and will fault if a start is attempted.

Values

The line phasing can be set to:

• INS - will run with either phase sequence
• ABC - will only run with ABC phase sequence
• CBA - will only run with CBA phase sequence

Default

The default value for the phase sensitivity parameter is INS.

Troubleshooting

The following troubleshooting charts can be used to help solve some of the more common
problems that occur.

Table 15, Motor will not start, no output to motor.

Display

Cause

Solution

Fault Displayed.

Shown on display.

See fault code table.

Watchdog LED on.

CPU card problem.

Consult McQuay Factory Service.

Display is blank.

Control voltage is absent.
FU1 on power card.
Ribbon Cables.

Check for proper control voltage.
Replace FU1.
Check ribbon cables.

Stopped

Control Devices
Display buttons disabled.

Check control devices
Enable display buttons.

No line

Missing at least one phase of main po Check power system.

Table 16, Motor rotates but does not reach full speed.

Display

Cause

Solution

Fault displayed.

Shown on display

See fault code table.

Accel or Running

Mechanical problems.
Abnormally low line voltage.

Check for load binding. Check motor.
Fix line voltage problem

Table 17, Deceleration profile not operating correctly.

Display

Cause

Solution

Motor stops too quickly.

Time setting. or improper level
setting.

Contact McQuay Factory

Service

Time seems correct but motor surges at start of
decel.

Decel level 1

Contact McQuay Factory

Service

Time seems correct but motor stops before cycle
complete.

Decel level 2.
TruTorque DCL End Torque

Contact McQuay Factory

Service

Time seems correct but water hammer occurs at
end of cycle.

Decel level 2.
TruTorque DCL End Torque

Contact McQuay Factory

Service

Table 18, Motor stops while running.

Display

Cause

Solution

Fault displayed.

Shown on display.

See fault code table.

Display is blank.

Control voltage is absent.
FU1 on power card

Check control wiring and voltage.
Replace fuse.

Stopped

Control devices.

Check control system.

Содержание RVSS14



































































Результаты поиска

Содержание RVSS14

Отзывы:

McQuay RVSS14, Инструкция по установке, эксплуатации и обслуживанию, Страница: 57 / 66

Результаты поиска

Содержание RVSS14

Отзывы: