McQuay RVSS14 Скачать руководство пользователя страница 46

Страница: 46 / 66

IOMM

Starter

Fault

Code

Description

Detailed Description of Fault / Possible Solutions

Based on the Analog Input parameter settings, the analog input level has either

exceeded or dropped below the Analog Input Trip Level setting (I/O 08,

P46

) for

longer than the Analog Input Trip Delay time (I/O 09, P47).

Measure value of analog input to verify correct reading.

Verify settings of all Analog Input parameters (I/O 07-11,

P45

-49).

Verify correct positioning of input jumper JP3 (Voltage or Current) on the D3 control

card.

F71

Analog Input

Level Fault Trip.

Verify correct grounding of analog input connection to prevent noise or ground loops

from affecting input.

Indicates that communication has been lost with a remote device such as a remote

keypad.

(This fault will normally occur if the remote keypad is disconnected while the D3

control board is powered up. Only connect and disconnect a remote keypad when the

control power is off.)

Verify that the remote keypad cable has not been damaged and that its connectors are

firmly seated at both the keypad and the D3 Control board.

Verify that the display interface board (when present) is firmly attached to D3 control

card.

F81

SPI

Communication

Fault

Route keypad cables away from high power and/or high noise areas to reduce possible

electrical noise pickup.

Indicates that the starter has lost serial communications. Fault occurs when the starter

has not received a valid serial communications within the Communication Timeout

parameter (FUN 12, P59) defined time.

Verify communication parameter settings (FUN 10-12, P59-P61).

Check wiring between the remote network and the D3 control card.

F82

Modbus

Timeout Fault

Examine remote system for cause of communication loss.

Typically occurs when attempting to run a version of control software that is

incompatible with the D3 control board hardware being used. Verify that the software

is a correct version for the D3 control board being used. Consult factory for more

details.

F94

CPU Error –

SW fault

Fault can also occur if the D3 control has detected an internal software problem.

Consult factory.

The non-volatile user parameter values have been found to be corrupted. Typically

occurs when the D3 control is re-flashed with new software.

F95

CPU Error –

Parameter

EEPROM

Checksum Fault

Perform a Factory Parameter reset and then properly set all user parameters before

resuming normal operation.

Содержание RVSS14



































































Результаты поиска

Содержание RVSS14

Отзывы:

McQuay RVSS14, Инструкция по установке, эксплуатации и обслуживанию, Страница: 46 / 66

Результаты поиска

Содержание RVSS14

Отзывы: