McQuay RVSS14 Скачать руководство пользователя страница 65

Страница: 65 / 66

IOMM Starter

Index of Figures & Tables

FIGURES

Figure 1, Wye-Delta Starter .................................................................................. 3

Figure 2, Solid State Starter, Wall Mounted ......................................................... 4

Figure 3, Starter Panel ........................................................................................ 14

Figure 4, Field Wiring for Optional D3 Communication.................................... 15

Figure 5, Control and Power Field Wiring.......................................................... 16

Figure 6, Optional Starter View Screen .............................................................. 27

Figure 7, Expanded Starter View Screen ............................................................ 28

Figure 8, Optional Starter Setpoint Screen ......................................................... 29

Figure 9, Starter-mounted LED .......................................................................... 30

Figure 10, Wye Delta Motor Connection to the D3 Control ............................... 37

Figure 11, Wye Delta Profile .............................................................................. 39

Figure 12, LED Display/Keypad ........................................................................ 52

TABLES

Table 1, Starter/VFD Mounting Arrangements ..................................................... 6

Table 2, Solid State Connection Sizes, Power Block.......................................... 10

Table 3, Solid State, Connection Sizes, Disconnect & Circuit Breaker ...............11

Table 4, Wye-Delta Connection Sizes, Standard Power Block ............................11

Table 5, Wye-Delta Connection Size, Disconnects & Circuit Breakers.............. 12

Table 6, Control Power Line Sizing.................................................................... 14

Table 7, Starter Setpoints.................................................................................... 29

Table 8, LED Special Characters Displayed ....................................................... 30

Table 9, Setpoints, Wye-Delta Starter................................................................. 32

Table 10, Setpoints, Solid State Starter............................................................... 33

Table 11, Status Messages, Wye-Delta Starter.................................................... 34

Table 12, Status Messages, Solid State Starter ................................................... 34

Table 13, Default Meter Display......................................................................... 35

Table 14, Main Menu.......................................................................................... 54

Table 15, Motor will not start, no output to motor. ............................................. 57

Table 16, Motor rotates but does not reach full speed. ....................................... 57

Table 17, Deceleration profile not operating correctly. ...................................... 57

Table 18, Motor stops while running. ................................................................. 57

Table 19, Other situations. .................................................................................. 58

Table 20, Fault/Log Codes.................................................................................. 59

Table 21, LED Diagnostics................................................................................. 62

Содержание RVSS14



































































Результаты поиска

Содержание RVSS14

Отзывы:

McQuay RVSS14, Инструкция по установке, эксплуатации и обслуживанию, Страница: 65 / 66

Результаты поиска

Содержание RVSS14

Отзывы: