Maxx 20569 Скачать руководство пользователя

Страница: 21 / 134

wood fibers is released.

15. Never cut in high wind, bad

weather, when visibility is poor

or in very high or low

temperatures. Always check the

tree for dead branches which

could fall during the felling

operation.

16. Keep the handles dry, Clean

and free of oil or fuel mixture.

17. Operate the chain saw only in

well ventilated areas. Never start

or run the engine inside a closed

room or building. Exh- aust

fumes contain dangerous

carbon monoxide.

18. Do not operate the chain saw in

a tree unless specially trained to

do so.

19. Guard against kickback. Kick-

back is the upward motion of the

guide bar which occurs when the

saw chain at the nose of the

guide bar contacts an object .

Kickback can lead to dangerous

loss of control of the chain saw .

20. When transporting your chain

saw, make sure the appropriate

guide bar scabbard is in place .

KICKBACK SAFETY PRECAU-

TIONS FOR CHAIN SAW USERS

WARNING

⚫

Kickback may occur when the

nose or tip of the guide bar

touches an object, or when the

wood closes in and pinches the

saw chain in the cut. Tip

contact in some cases may

cause a lightning fast reverse

reaction, kicking the guide bar

up and back towards the

operator. Pinching the saw

chain along the top of the guide

bar may push the guide bar

rapidly back towards the

operator. Enter of these rea-

ction may cause you to lose

control of the saw, Which could

result in serious personal

injury.

⚫

Do not rely exclusively on the

safety devices built into your

saw. As a chain saw user you

should take several steps to

keep cutting jobs free from

accident or injury.

With a basic understanding of

kickback you can reduce or

eliminate the element of surp-

rise. Sudden surprise contribu-

tes to accidents.

Keep a good grip on the saw

with both hands on the rear

handle, and the left hand on the

front handle, when the engine is

running . Use a firm grip with

thumbs and fingers encircling

the chain saw hand- les. A firm

grip will help you reduce

kickback and maintain control of

the saw.

Make certain that the area in

which you are cutting is free

from obstructions. Do not let the

nose of the guide bar contact a

log, branch, or any other

obstruction, which could be hit

while you are operating the saw.

Cut at high engine speeds.

Do not overreach or cut above

shoulder height.

Follow the manufacturer

’

s sha-

rpening and maintenance inst-

ructions for the saw chain .

Only use replacement bars and

chains

specified

by the

manufacturer of the equivalent

wood fibers is released.

15. Never cut in high wind, bad

weather, when visibility is poor

or in very high or low

temperatures. Always check the

tree for dead branches which

could fall during the felling

operation.

16. Keep the handles dry, Clean

and free of oil or fuel mixture.

17. Operate the chain saw only in

well ventilated areas. Never start

or run the engine inside a closed

room or building. Exh- aust

fumes contain dangerous

carbon monoxide.

18. Do not operate the chain saw in

a tree unless specially trained to

do so.

19. Guard against kickback. Kick-

back is the upward motion of the

guide bar which occurs when the

saw chain at the nose of the

guide bar contacts an object .

Kickback can lead to dangerous

loss of control of the chain saw .

20. When transporting your chain

saw, make sure the appropriate

guide bar scabbard is in place .

KICKBACK SAFETY PRECAU-

TIONS FOR CHAIN SAW USERS

WARNING

⚫

Kickback may occur when the

nose or tip of the guide bar

touches an object, or when the

wood closes in and pinches the

saw chain in the cut. Tip

contact in some cases may

cause a lightning fast reverse

reaction, kicking the guide bar

up and back towards the

operator. Pinching the saw

chain along the top of the guide

bar may push the guide bar

rapidly back towards the

operator. Enter of these rea-

ction may cause you to lose

control of the saw, Which could

result in serious personal

injury.

⚫

Do not rely exclusively on the

safety devices built into your

saw. As a chain saw user you

should take several steps to

keep cutting jobs free from

accident or injury.

With a basic understanding of

kickback you can reduce or

eliminate the element of surp-

rise. Sudden surprise contribu-

tes to accidents.

Keep a good grip on the saw

with both hands on the rear

handle, and the left hand on the

front handle, when the engine is

running . Use a firm grip with

thumbs and fingers encircling

the chain saw hand- les. A firm

grip will help you reduce

kickback and maintain control of

the saw.

Make certain that the area in

which you are cutting is free

from obstructions. Do not let the

nose of the guide bar contact a

log, branch, or any other

obstruction, which could be hit

while you are operating the saw.

Cut at high engine speeds.

Do not overreach or cut above

shoulder height.

Follow the manufacturer

’

s sha-

rpening and maintenance inst-

ructions for the saw chain .

Only use replacement bars and

chains

specified

by the

manufacturer of the equivalent

wood fibers is released.

15. Never cut in high wind, bad

weather, when visibility is poor

or in very high or low

temperatures. Always check the

tree for dead branches which

could fall during the felling

operation.

16. Keep the handles dry, Clean

and free of oil or fuel mixture.

17. Operate the chain saw only in

well ventilated areas. Never start

or run the engine inside a closed

room or building. Exh- aust

fumes contain dangerous

carbon monoxide.

18. Do not operate the chain saw in

a tree unless specially trained to

do so.

19. Guard against kickback. Kick-

back is the upward motion of the

guide bar which occurs when the

saw chain at the nose of the

guide bar contacts an object .

Kickback can lead to dangerous

loss of control of the chain saw .

20. When transporting your chain

saw, make sure the appropriate

guide bar scabbard is in place .

KICKBACK SAFETY PRECAU-

TIONS FOR CHAIN SAW USERS

WARNING

⚫

Kickback may occur when the

nose or tip of the guide bar

touches an object, or when the

wood closes in and pinches the

saw chain in the cut. Tip

contact in some cases may

cause a lightning fast reverse

reaction, kicking the guide bar

up and back towards the

operator. Pinching the saw

chain along the top of the guide

bar may push the guide bar

rapidly back towards the

operator. Enter of these rea-

ction may cause you to lose

control of the saw, Which could

result in serious personal

injury.

⚫

Do not rely exclusively on the

safety devices built into your

saw. As a chain saw user you

should take several steps to

keep cutting jobs free from

accident or injury.

With a basic understanding of

kickback you can reduce or

eliminate the element of surp-

rise. Sudden surprise contribu-

tes to accidents.

Keep a good grip on the saw

with both hands on the rear

handle, and the left hand on the

front handle, when the engine is

running . Use a firm grip with

thumbs and fingers encircling

the chain saw hand- les. A firm

grip will help you reduce

kickback and maintain control of

the saw.

Make certain that the area in

which you are cutting is free

from obstructions. Do not let the

nose of the guide bar contact a

log, branch, or any other

obstruction, which could be hit

while you are operating the saw.

Cut at high engine speeds.

Do not overreach or cut above

shoulder height.

Follow the manufacturer

’

s sha-

rpening and maintenance inst-

ructions for the saw chain .

Only use replacement bars and

chains

specified

by the

manufacturer of the equivalent

wood fibers is released.

15. Never cut in high wind, bad

weather, when visibility is poor

or in very high or low

temperatures. Always check the

tree for dead branches which

could fall during the felling

operation.

16. Keep the handles dry, Clean

and free of oil or fuel mixture.

17. Operate the chain saw only in

well ventilated areas. Never start

or run the engine inside a closed

room or building. Exh- aust

fumes contain dangerous

carbon monoxide.

18. Do not operate the chain saw in

a tree unless specially trained to

do so.

19. Guard against kickback. Kick-

back is the upward motion of the

guide bar which occurs when the

saw chain at the nose of the

guide bar contacts an object .

Kickback can lead to dangerous

loss of control of the chain saw .

20. When transporting your chain

saw, make sure the appropriate

guide bar scabbard is in place .

KICKBACK SAFETY PRECAU-

TIONS FOR CHAIN SAW USERS

WARNING

⚫

Kickback may occur when the

nose or tip of the guide bar

touches an object, or when the

wood closes in and pinches the

saw chain in the cut. Tip

contact in some cases may

cause a lightning fast reverse

reaction, kicking the guide bar

up and back towards the

operator. Pinching the saw

chain along the top of the guide

bar may push the guide bar

rapidly back towards the

operator. Enter of these rea-

ction may cause you to lose

control of the saw, Which could

result in serious personal

injury.

⚫

Do not rely exclusively on the

safety devices built into your

saw. As a chain saw user you

should take several steps to

keep cutting jobs free from

accident or injury.

With a basic understanding of

kickback you can reduce or

eliminate the element of surp-

rise. Sudden surprise contribu-

tes to accidents.

Keep a good grip on the saw

with both hands on the rear

handle, and the left hand on the

front handle, when the engine is

running . Use a firm grip with

thumbs and fingers encircling

the chain saw hand- les. A firm

grip will help you reduce

kickback and maintain control of

the saw.

Make certain that the area in

which you are cutting is free

from obstructions. Do not let the

nose of the guide bar contact a

log, branch, or any other

obstruction, which could be hit

while you are operating the saw.

Cut at high engine speeds.

Do not overreach or cut above

shoulder height.

Follow the manufacturer

’

s sha-

rpening and maintenance inst-

ructions for the saw chain .

Only use replacement bars and

chains

specified

by the

manufacturer of the equivalent

wood fibers is released.

15. Never cut in high wind, bad

weather, when visibility is poor

or in very high or low

temperatures. Always check the

tree for dead branches which

could fall during the felling

operation.

16. Keep the handles dry, Clean

and free of oil or fuel mixture.

17. Operate the chain saw only in

well ventilated areas. Never start

or run the engine inside a closed

room or building. Exh- aust

fumes contain dangerous

carbon monoxide.

18. Do not operate the chain saw in

a tree unless specially trained to

do so.

19. Guard against kickback. Kick-

back is the upward motion of the

guide bar which occurs when the

saw chain at the nose of the

guide bar contacts an object .

Kickback can lead to dangerous

loss of control of the chain saw .

20. When transporting your chain

saw, make sure the appropriate

guide bar scabbard is in place .

KICKBACK SAFETY PRECAU-

TIONS FOR CHAIN SAW USERS

WARNING

⚫

Kickback may occur when the

nose or tip of the guide bar

touches an object, or when the

wood closes in and pinches the

saw chain in the cut. Tip

contact in some cases may

cause a lightning fast reverse

reaction, kicking the guide bar

up and back towards the

operator. Pinching the saw

chain along the top of the guide

bar may push the guide bar

rapidly back towards the

operator. Enter of these rea-

ction may cause you to lose

control of the saw, Which could

result in serious personal

injury.

⚫

Do not rely exclusively on the

safety devices built into your

saw. As a chain saw user you

should take several steps to

keep cutting jobs free from

accident or injury.

With a basic understanding of

kickback you can reduce or

eliminate the element of surp-

rise. Sudden surprise contribu-

tes to accidents.

Keep a good grip on the saw

with both hands on the rear

handle, and the left hand on the

front handle, when the engine is

running . Use a firm grip with

thumbs and fingers encircling

the chain saw hand- les. A firm

grip will help you reduce

kickback and maintain control of

the saw.

Make certain that the area in

which you are cutting is free

from obstructions. Do not let the

nose of the guide bar contact a

log, branch, or any other

obstruction, which could be hit

while you are operating the saw.

Cut at high engine speeds.

Do not overreach or cut above

shoulder height.

Follow the manufacturer

’

s sha-

rpening and maintenance inst-

ructions for the saw chain .

Only use replacement bars and

chains

specified

by the

manufacturer of the equivalent

wood fibers is released.

15. Never cut in high wind, bad

weather, when visibility is poor

or in very high or low

temperatures. Always check the

tree for dead branches which

could fall during the felling

operation.

16. Keep the handles dry, Clean

and free of oil or fuel mixture.

17. Operate the chain saw only in

well ventilated areas. Never start

or run the engine inside a closed

room or building. Exh- aust

fumes contain dangerous

carbon monoxide.

18. Do not operate the chain saw in

a tree unless specially trained to

do so.

19. Guard against kickback. Kick-

back is the upward motion of the

guide bar which occurs when the

saw chain at the nose of the

guide bar contacts an object .

Kickback can lead to dangerous

loss of control of the chain saw .

20. When transporting your chain

saw, make sure the appropriate

guide bar scabbard is in place .

KICKBACK SAFETY PRECAU-

TIONS FOR CHAIN SAW USERS

WARNING

⚫

Kickback may occur when the

nose or tip of the guide bar

touches an object, or when the

wood closes in and pinches the

saw chain in the cut. Tip

contact in some cases may

cause a lightning fast reverse

reaction, kicking the guide bar

up and back towards the

operator. Pinching the saw

chain along the top of the guide

bar may push the guide bar

rapidly back towards the

operator. Enter of these rea-

ction may cause you to lose

control of the saw, Which could

result in serious personal

injury.

⚫

Do not rely exclusively on the

safety devices built into your

saw. As a chain saw user you

should take several steps to

keep cutting jobs free from

accident or injury.

With a basic understanding of

kickback you can reduce or

eliminate the element of surp-

rise. Sudden surprise contribu-

tes to accidents.

Keep a good grip on the saw

with both hands on the rear

handle, and the left hand on the

front handle, when the engine is

running . Use a firm grip with

thumbs and fingers encircling

the chain saw hand- les. A firm

grip will help you reduce

kickback and maintain control of

the saw.

Make certain that the area in

which you are cutting is free

from obstructions. Do not let the

nose of the guide bar contact a

log, branch, or any other

obstruction, which could be hit

while you are operating the saw.

Cut at high engine speeds.

Do not overreach or cut above

shoulder height.

Follow the manufacturer

’

s sha-

rpening and maintenance inst-

ructions for the saw chain .

Only use replacement bars and

chains

specified

by the

manufacturer of the equivalent

wood fibers is released.

15. Never cut in high wind, bad

weather, when visibility is poor

or in very high or low

temperatures. Always check the

tree for dead branches which

could fall during the felling

operation.

16. Keep the handles dry, Clean

and free of oil or fuel mixture.

17. Operate the chain saw only in

well ventilated areas. Never start

or run the engine inside a closed

room or building. Exh- aust

fumes contain dangerous

carbon monoxide.

18. Do not operate the chain saw in

a tree unless specially trained to

do so.

19. Guard against kickback. Kick-

back is the upward motion of the

guide bar which occurs when the

saw chain at the nose of the

guide bar contacts an object .

Kickback can lead to dangerous

loss of control of the chain saw .

20. When transporting your chain

saw, make sure the appropriate

guide bar scabbard is in place .

KICKBACK SAFETY PRECAU-

TIONS FOR CHAIN SAW USERS

WARNING

⚫

Kickback may occur when the

nose or tip of the guide bar

touches an object, or when the

wood closes in and pinches the

saw chain in the cut. Tip

contact in some cases may

cause a lightning fast reverse

reaction, kicking the guide bar

up and back towards the

operator. Pinching the saw

chain along the top of the guide

bar may push the guide bar

rapidly back towards the

operator. Enter of these rea-

ction may cause you to lose

control of the saw, Which could

result in serious personal

injury.

⚫

Do not rely exclusively on the

safety devices built into your

saw. As a chain saw user you

should take several steps to

keep cutting jobs free from

accident or injury.

With a basic understanding of

kickback you can reduce or

eliminate the element of surp-

rise. Sudden surprise contribu-

tes to accidents.

Keep a good grip on the saw

with both hands on the rear

handle, and the left hand on the

front handle, when the engine is

running . Use a firm grip with

thumbs and fingers encircling

the chain saw hand- les. A firm

grip will help you reduce

kickback and maintain control of

the saw.

Make certain that the area in

which you are cutting is free

from obstructions. Do not let the

nose of the guide bar contact a

log, branch, or any other

obstruction, which could be hit

while you are operating the saw.

Cut at high engine speeds.

Do not overreach or cut above

shoulder height.

Follow the manufacturer

’

s sha-

rpening and maintenance inst-

ructions for the saw chain .

Only use replacement bars and

chains

specified

by the

manufacturer of the equivalent

Ne coupez jamais par grand

vent, par mauvais temps, par

mauvaise visibilité ou par très

hautes ou basses températu-

res. Vérifiez toujours que l’ar

bre ne contient pas de bran-

ches mortes pouvant tomber

lors de l’abattage.
Gardez les poignées sèches,

propres et exemptes d’huile

ou de mélange de carburant.
Utilisez la tronçonneuse uni-

quement dans des zones

bien ventilées. Ne démarrez

ou ne faites jamais tourner le

moteur dans un espace ou

un bâtiment clos. Les vapeurs

d’explosion contiennent du

monoxyde de carbone dan-

gereux.

N’utilisez pas la tronçonneuse

dans un arbre à moins d’avoir

été spécialement formé à cet

effet.

Lorsque vous transportez vot-

re scie à chaîne, assurez-vous

que la bonne barre est en

place.

Un recul peut se produire

lorsque le nez ou la pointe

du guide de scie touche un

objet, ou lorsque le bois se

ferme et que la chaîne de

scie se coince dans la coupe.

Dans certains cas, le contact

de la pointe peut provoquer

une réaction rapide comme

l’éclair, ce qui provoque le

soulèvement et le retour de la

lame de scie vers l’opérateur.

Cela peut entraîner des bles-

sures graves.

Protège contre le rebond.

Le recul est le mouvement

ascendant de la tige de gui-

dage qui se produit lorsque

la chaîne de scie située sur le

nez de la tige de guidage en-

tre en contact avec un objet.

Le recul peut entraîner une

perte de contrôle dangereu-

se de la tronçonneuse.

15.

16.

17.

18.

20.

•

19.

Avec une connaissance de base

du recul, vous pouvez réduire ou

éliminer l’élément de surprise. La

surprise soudaine contribue aux

accidents.
Tenez bien la scie avec les deux

mains sur la poignée arrière et

la main gauche sur la poignée

avant lorsque le moteur tourne.

Utilisez une poignée solide avec

les pouces et les doigts autour des

poignées de la tronçonneuse. Une

prise ferme vous aide à réduire les

contrecoups et à garder le con-

trôle de la scie.
Assurez-vous que la zone dans

laquelle vous coupez est libre

d’obstacles. Ne laissez pas le nez

de la lame de scie entrer en con-

tact avec un tronc d’arbre, une

branche ou tout autre obstacle

pouvant être touché lors de l’uti-

lisation de la scie.
Vu à haut régime moteur.
Ne coupez pas au-dessus de vos

épaules et hors de votre portée.
Suivez les instructions d’installation

et de maintenance du fabricant

pour la chaîne de scie.
Utilisez uniquement des lames et

des chaînes de rechange spéci-

fiées par le fabricant du produit.

4.
5.

KICK BACK PRECAUTIONS DE SECURITE

POUR CAINSAW UTILISATEURS

Ne comptez pas uniquement sur

les fonctions de sécurité intégrées

à votre scie. En tant qu’utilisateur

de scie à chaîne, vous devez

prendre diverses mesures pour évi-

ter les accidents ou les blessures

pendant le travail de sciage.

Содержание 20569







































































































































Результаты поиска

Содержание 20569

Отзывы:

Похожие инструкции для 20569

Бренды по названию

Популярные бренды

Maxx 20569, Руководство пользователя

Результаты поиска

Содержание 20569

Отзывы:

Похожие инструкции для 20569

Бренды по названию

Популярные бренды