Maxx 20569, Руководство пользователя

Страница: 78 / 134

78
Tanque de aceite
Retire el filtro de aceite con un gancho de
alambre a través del orificio de llenado y lím -
pielo con gasolina. Cuando vuelva a colocar
el filtro en el tanque, asegúrese de que esté
en la esquina inferior derecha. También elimi-
ne cualquier residuo en el tanque.
Bujía
Limpie los electrodos con un cepillo de alam-
bre y restablezca el espacio a 0,65 mm si es
necesario.
Cadena de sierra
Es muy importante para un funciona-
miento suave y seguro mantener las
cuchillas afiladas en todo momento.
Las cuchillas deben afilarse cuando:
• El aserrín se vuelve polvoriento.
• Necesita fuerza adicional para cortar.
• El camino de corte no va recto
• Las vibraciones aumentan.
• Aumenta el consumo de combustible
Asegúrese de usar guantes de
seguridad.
Tandwiel
Controleer op barsten en overmatige slijtage
die de kettingaandrijving verstoort. Als de slij-
tage aanzienlijk is, vervangt u deze door een
nieuwe. Monteer nooit een nieuwe ketting op
een versleten tandwiel of een versleten ket-
ting op een nieuw tandwiel.
8. MANTENIMIENTO DE LA CADENA Y LA BARRA
DE LA SIERRA
Snijstandaard normen:
Antes de llenar:
• Asegúrese de que la cadena de la sierra esté
bien sujeta.
• Asegúrese de que el motor esté parado.
• Utilice una lima redonda del tamaño correcto
para la cadena.
Model 20569
Pitch (in.(mm)) 120” (1.27mm)
3. Oil tank
With a wire hook, take out the oil filter through the
filler port and clean in gasoline. When putting the
filter back into the tank, make sure that it comes
to the front right corner. Also clean off dirt in the
tank.
4. Spark plug
Clean the electrodes with a wire brush and reset
the gap to 0.65 mm as necessary.
5. Sprocket
Check for cracks and for excessive wear
interfering with the chain drive. If the wear is
considerable, replace it with new one. Never fit a
new chain on a worn sprocket, or a worn chain on
a new sprocket.
8. Maintenance of Saw Chain and Guide Bar

Saw Chain
Place the file on the cutter and push straight
forward.
Keep the file position as illustrated.
Cutter setting standards:
Before filling:
⚫
Make sure the saw chain is held securely.
⚫
Make sure the engine is stopped.
⚫
Use a round file of proper size for the chain .
Model 20569
Pitch (in.(mm)) 1/20 ” (1.27mm)
After each cutter has been filed, check the depth
gauge and file it to the proper level as illustrated.
Be sure to wear safety gloves.
It is very important for smooth and safe
operation to always keep the cutters
sharp.
The cutters need to be sharpened when:
⚫
Sawdust becomes powder-like.
⚫
You need extra force to saw in.
⚫
The cut path does not go straight.
⚫
Vibration increases.
⚫
Fuel consumption increases.
3. Oil tank
With a wire hook, take out the oil filter through the
filler port and clean in gasoline. When putting the
filter back into the tank, make sure that it comes
to the front right corner. Also clean off dirt in the
tank.
4. Spark plug
Clean the electrodes with a wire brush and reset
the gap to 0.65 mm as necessary.
5. Sprocket
Check for cracks and for excessive wear
interfering with the chain drive. If the wear is
considerable, replace it with new one. Never fit a
new chain on a worn sprocket, or a worn chain on
a new sprocket.
8. Maintenance of Saw Chain and Guide Bar

Saw Chain
Place the file on the cutter and push straight
forward.
Keep the file position as illustrated.
Cutter setting standards:
Before filling:
⚫
Make sure the saw chain is held securely.
⚫
Make sure the engine is stopped.
⚫
Use a round file of proper size for the chain .
Model 20569
Pitch (in.(mm)) 1/20 ” (1.27mm)
After each cutter has been filed, check the depth
gauge and file it to the proper level as illustrated.
Be sure to wear safety gloves.
It is very important for smooth and safe
operation to always keep the cutters
sharp.
The cutters need to be sharpened when:
⚫
Sawdust becomes powder-like.
⚫
You need extra force to saw in.
⚫
The cut path does not go straight.
⚫
Vibration increases.
⚫
Fuel consumption increases.
3. Oil tank
With a wire hook, take out the oil filter through the
filler port and clean in gasoline. When putting the
filter back into the tank, make sure that it comes
to the front right corner. Also clean off dirt in the
tank.
4. Spark plug
Clean the electrodes with a wire brush and reset
the gap to 0.65 mm as necessary.
5. Sprocket
Check for cracks and for excessive wear
interfering with the chain drive. If the wear is
considerable, replace it with new one. Never fit a
new chain on a worn sprocket, or a worn chain on
a new sprocket.
8. Maintenance of Saw Chain and Guide Bar

Saw Chain
Place the file on the cutter and push straight
forward.
Keep the file position as illustrated.
Cutter setting standards:
Before filling:
⚫
Make sure the saw chain is held securely.
⚫
Make sure the engine is stopped.
⚫
Use a round file of proper size for the chain .
Model 20569
Pitch (in.(mm)) 1/20 ” (1.27mm)
After each cutter has been filed, check the depth
gauge and file it to the proper level as illustrated.
Be sure to wear safety gloves.
It is very important for smooth and safe
operation to always keep the cutters
sharp.
The cutters need to be sharpened when:
⚫
Sawdust becomes powder-like.
⚫
You need extra force to saw in.
⚫
The cut path does not go straight.
⚫
Vibration increases.
⚫
Fuel consumption increases.
3. Oil tank
With a wire hook, take out the oil filter through the
filler port and clean in gasoline. When putting the
filter back into the tank, make sure that it comes
to the front right corner. Also clean off dirt in the
tank.
4. Spark plug
Clean the electrodes with a wire brush and reset
the gap to 0.65 mm as necessary.
5. Sprocket
Check for cracks and for excessive wear
interfering with the chain drive. If the wear is
considerable, replace it with new one. Never fit a
new chain on a worn sprocket, or a worn chain on
a new sprocket.
8. Maintenance of Saw Chain and Guide Bar

Saw Chain
Place the file on the cutter and push straight
forward.
Keep the file position as illustrated.
Cutter setting standards:
Before filling:
⚫
Make sure the saw chain is held securely.
⚫
Make sure the engine is stopped.
⚫
Use a round file of proper size for the chain .
Model 20569
Pitch (in.(mm)) 1/20 ” (1.27mm)
After each cutter has been filed, check the depth
gauge and file it to the proper level as illustrated.
Be sure to wear safety gloves.
It is very important for smooth and safe
operation to always keep the cutters
sharp.
The cutters need to be sharpened when:
⚫
Sawdust becomes powder-like.
⚫
You need extra force to saw in.
⚫
The cut path does not go straight.
⚫
Vibration increases.
⚫
Fuel consumption increases.
3. Oil tank
With a wire hook, take out the oil filter through the
filler port and clean in gasoline. When putting the
filter back into the tank, make sure that it comes
to the front right corner. Also clean off dirt in the
tank.
4. Spark plug
Clean the electrodes with a wire brush and reset
the gap to 0.65 mm as necessary.
5. Sprocket
Check for cracks and for excessive wear
interfering with the chain drive. If the wear is
considerable, replace it with new one. Never fit a
new chain on a worn sprocket, or a worn chain on
a new sprocket.
8. Maintenance of Saw Chain and Guide Bar

Saw Chain
Place the file on the cutter and push straight
forward.
Keep the file position as illustrated.
Cutter setting standards:
Before filling:
⚫
Make sure the saw chain is held securely.
⚫
Make sure the engine is stopped.
⚫
Use a round file of proper size for the chain .
Model 20569
Pitch (in.(mm)) 1/20 ” (1.27mm)
After each cutter has been filed, check the depth
gauge and file it to the proper level as illustrated.
Be sure to wear safety gloves.
It is very important for smooth and safe
operation to always keep the cutters
sharp.
The cutters need to be sharpened when:
⚫
Sawdust becomes powder-like.
⚫
You need extra force to saw in.
⚫
The cut path does not go straight.
⚫
Vibration increases.
⚫
Fuel consumption increases.
Nadat elk mes is bijgevuld, controleert u de
dieptemeter en vijlt u deze op het juiste niveau
zoals afgebeeld.