MaxPro PROFESSIONAL 111-0002, Руководство пользователя, Страница: 7 / 47

8 9 GB GB
Buffing
1.Remove the guard
2.Mount a buffing disc.
3.Turn on the device and allow it to run without applying a load.
4.Buff the surface using uniform circular movements.
Cut-off grinding
Risk of injury!
When using cutting discs, splinters may come away from the cutting disc during cutting and spin off. When
cutting, we recommend use the special protective cover.
High risk of injury!
Fragments of cut-off discs may be projected at a very high velocity.
- Do not apply any lateral pressure to the disc as the cut-off disc may tilt and burst.
1.Remove the protective special cover
2.Attach the protective cover
3.Mount a cut-off disc.
4.Turn on the device and allow it to run without applying a load.
5.Hold the motor block at an angle of 300 to 450 to the work piece.
6.Slowly and evenly run the disc along the designated cut-off line.
CLEANING AND MAINTANCE
Before any work on the machine itself, pull the mains plug. For safe and proper working, always keep the
machine and ventilation slots clean. In extreme working conditions, conductive dust can accumulate in
the interior of the machine when working with metal. The protective insulation of the machine can be
degraded. The use of a stationary extraction system is recommended in such cases as well as frequently
blowing out the ventilation slots and installing a residual current device (RCD). Please store and handle
the accessory(-ies) carefully. If the machine should fail despite the care taken in manufacturing and testing
procedures, repair should be carried out by an after-sales service centre for Maxpro power tools.
ENVIRONMENT
Do not dispose of electric tools, accessories and packaging together with household waste material -
in observance of European Directive 2002/96/EC on waste of electric and electronic equipment and its
implementation in accordance with national law, electric tools that have reached the end of their life must
be collected separately and returned to an environmentally compatible recycling facility.
TROUBLE SHOOTING
Fault Symptom Possible Cause Troubleshooting
Out of service Disconnection between plug and
power socket
Put plug in power socket
shortcircuit in power supply Repair and reconnection
At switch-off Switch on
Loose switching contact Replace switchboard by repairer
Damage in soft starting block Replace soft starting block by repairer
Burnout of stator or rotor coil Replace stator or rotor by repairer
Stator wiring disconnection Reconnection by repairer
Disconnection between carbon brush
and commutator
Replace carbon brush
Sluggish start-up, falling short
of running speed
Unsmooth running in mechanical
part
Check mechanical part by repairer
Low supply voltage Regulate supply voltage
Burnout of switch contact Replace switchboard by repairer
Excessive sparkling during
running
Underpressure in carbon brush spring Replace carbon brush by reparier
Excessive wearout of carbon brush Replace carbon brush by reparier
Ring fire caused by shortcircuit in
rotor winding shortcircuit
Check or replace rotor by repairer
Ring fire caused by shortcircuit in
commutator segment
Check or replace rotor by repairer
Overvoltage in supply power Regulate supply voltage
Disconnection between carbon brush
and commutator
Replace carbon brush
Excessive machinery noise Motor failure, edge friction or
bearing damage
Check or replace motor or bearing by
repairer
Gear wheel failure Replace gear wheel or rotor by
repairer
Failed to reach rated power Electrocircuit overload due to lighting
device, public utility or other electric
appliances
No use of public utility or other
electric appliances on machine-
connected electrocircuit
Machine superheating Electromotor overload Overload protection
Insufficient motor cooling Dedust air outlet
Excessive mechanical
vibration
Rotor damage Replace electric machine rotor by
repairer
Gear wheel damage Replace gear wheel or rotor by
repairer
Improper installation of cutting blade
or grinding disc
Redo with reference to installation
specification
Substandard cutting effect or
grinding effect
Severe wear of cutting blade or
grinding disc
Replace cutting blade or grinding disc
Spare parts list and drawing Please download files on www.maxpro-tools.com